manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

11

cruising.

(See 

NO.11 ENGINE 

STALLS/QUITS, ENGINE 

RUNS ROUGH, MISSES, 
BUCK/JERK, 

HESITATION/STUMBLE, 
SURGES [MZI-3.5]

.)

Engine runs 

rough.

Acceleration/cruise

The engine speed 

fluctuates during 
acceleration or 

cruising.

Misses

Acceleration/cruise

The engine misses 
during acceleration or 

cruising.

Buck/jerk

Acceleration/cruise/deceleration The vehicle 

bucks/jerks during 
acceleration, cruising, 

or deceleration.

Hesitation/stumble Acceleration

A momentary pause at 
the beginning of 

acceleration or during 
acceleration.

Surges

Acceleration/cruise

A momentary minor 

irregularity in engine 
output.

12

Lack/loss of 

power

Acceleration/cruise

The performance is 
poor under load (such 

as power down when 
climbing hills).

(See 

NO.12 LACK/LOSS OF 

POWER-

ACCELERATION/CRUISE 
[MZI-3.5]

.)

13 Knocking/pinging Acceleration/cruise

Sound is produced 

when the air/fuel 
mixture is ignited by 

something other than 
the spark plug (such 

as hot spot in 
combustion chamber).

(See 

NO.13 

KNOCKING/PINGING-
ACCELERATION/CRUISE 

[MZI-3.5]

.)

14

Poor fuel economy

The fuel economy is 
unsatisfactory.

(See 

NO.14 POOR FUEL 

ECONOMY [MZI-3.5]

.)

15 Emission compliance

Fails emissions test.

(see 

NO.15 EMISSION 

COMPLIANCE [MZI-3.5]

.)

16 High oil consumption/leakage

The oil consumption 
is excessive.

(See 

NO.16 HIGH OIL 

CONSUMPTION/LEAKAGE 

[MZI-3.5]

.)

17 Cooling system 

concerns

Overheating

The engine runs at 

higher than normal 
temperature/overheats.

(See 

NO.17 COOLING 

SYSTEM CONCERNS-
OVERHEATING [MZI-3.5]

.)

18 Cooling system 

concerns

Runs cold

The engine does not 

reach normal 
operating temperature.

(See 

NO.18 COOLING 

SYSTEM CONCERNS-
RUNS COLD [MZI-3.5]

.)

19 Exhaust smoke

Blue, black, or white 
smoke from exhaust 

(See 

NO.19 EXHAUST 

SMOKE [MZI-3.5]

.)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:36 AM

Page 3 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Lincoln 2015 MKS Owner'S Manual preview
2015 MKS
Бренд: Lincoln Страницы: 424
Volkswagen 1983 Camper Onwers Manual preview
1983 Camper
Бренд: Volkswagen Страницы: 26
Farad BARS PR25 - 2 Quick Start Manual preview
BARS PR25 - 2
Бренд: Farad Страницы: 8
Mazda 2 2016 Owner'S Manual preview
2 2016
Бренд: Mazda Страницы: 720
Dodge 8W-30 Wiring Diagram preview
8W-30
Бренд: Dodge Страницы: 24
CTEK D250S Dual Manual preview
D250S Dual
Бренд: CTEK Страницы: 84
Metra Electronics 99-7477 Installation Instructions preview
99-7477
Бренд: Metra Electronics Страницы: 2
ACV 281178-28G-M Installation Manual preview
281178-28G-M
Бренд: ACV Страницы: 2
Gator GHWCUSB2 User Manual preview
GHWCUSB2
Бренд: Gator Страницы: 8
benbat BM721 Instructions For Use Manual preview
BM721
Бренд: benbat Страницы: 14
SPL FE Z33 Installation Instructions preview
FE Z33
Бренд: SPL Страницы: 5
Flash Cover MN019 Instructions preview
MN019
Бренд: Flash Cover Страницы: 2
Porsche WTY 2010 Warranty & Maintenance Manual preview
WTY 2010
Бренд: Porsche Страницы: 98
Havis C-DMM-3005 Installation Instructions preview
C-DMM-3005
Бренд: Havis Страницы: 5
Cadillac 2000 DeVille Service Manual Addendum preview
2000 DeVille
Бренд: Cadillac Страницы: 19
Ford transit connect 2012 User Manual preview
transit connect 2012
Бренд: Ford Страницы: 299
APS iBoard IB-R159 Manual preview
iBoard IB-R159
Бренд: APS Страницы: 4
ULTIMATE SPEED 1188 1525 Instructions For Use And Safety Manuallines preview
1188 1525
Бренд: ULTIMATE SPEED Страницы: 26

Бренды по названию

Популярные бренды

Загрузить еще бренды