Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 492

Страница: 492 / 1056

been recorded?

VERIFY RELATED REPAIR

INFORMATION AVAILABILITY

Verify related Service Bulletins
and/or on-line repair information

availability.

Is any related Service Bulletins
available?

Yes

Perform repair or diagnosis according to

the available Service Bulletins.

If the vehicle is not repaired, go to
the next step.

Go to the next step.

INSPECT TP SENSOR
CONNECTOR FOR POOR

CONNECTION

Turn the ignition switch off.

Disconnect the throttle body
connector.

Inspect for poor connection (such

as damaged/pulled-out pins,

corrosion).

Are there any malfunction?

Yes

Repair or replace suspected part, then go to
Step 8.

Go to the next step.

INSPECT PCM CONNECTOR FOR
POOR CONNECTION

Turn the ignition switch off.

Disconnect the PCM connector.

Inspect for poor connection (such
as damaged/pulled-out pins,

corrosion).

Are there any malfunction?

Yes

Repair or replace suspected part, then go to
Step 8.

Go to the next step.

INSPECT TP SIGNAL CIRCUIT
FOR OPEN CIRCUIT

Turn the ignition switch off.

Disconnect the PCM connector.

Disconnect the throttle body
connector.

Inspect for continuity between the

following terminals:.

{

Throttle body terminal C
and PCM terminal 2AD

{

Throttle body terminal D

and PCM terminal 2D

Are there continuity?

Yes

Go to the next step.

Repair or replace suspected part, then go to
Step 8.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:31 AM

Page 145

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды