manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

DTC P0606 [MZI-3.5] 

DTC P0606 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

 

DIAGNOSTIC PROCEDURE 

DTC P0606 (MZI-3.5) DIAGNOSTIC PROCEDURE

 

memory using the M-MDS.  

z

Perform the "KOEO and KOER 

self-test". 

(See 

KOEO/KOER SELF TEST 

[MZI-3.5]

.) 

z

Retrieve DTCs using the M-MDS. 

z

Is the PENDING CODE for this 
DTC present?  

No

Go to next step.

4

VERIFY AFTER REPAIR 

PROCEDURE

 

z

Perform the "AFTER REPAIR 
PRECAUTION". 

(See 

AFTER REPAIR 

PROCEDURE [MZI-3.5]

.) 

z

Are any DTCs present?  

Yes

Go to the applicable DTC inspection. 

(See 

DTC TABLE [MZI-3.5]

.)

No

Troubleshooting completed.

DTC P0606

ECM/PCM processor

DETECTION 
CONDITION

 

z

This DTC indicates a register hardback (PCM internal communications) 
error.  

POSSIBLE CAUSE

 

z

PCM malfunction  

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA 

HAS BEEN RECORDED

 

z

Has FREEZE FRAME DATA 
been recorded?  

Yes

Go to the next step.

No

Record FREEZE FRAME DATA on the 

repair order, then go to the next step.

2

VERIFY RELATED REPAIR 
INFORMATION AVAILABILITY

 

z

Verify related Service Bulletins 

and/or on-line repair information 
availability.  

Yes

Perform repair or diagnosis according to 
the available Service Bulletins. 

z

If the vehicle is not repaired, go to 

the next step.  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:34 AM

Page 286 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

N-Com B3 User Instructions And Safety preview
B3
Бренд: N-Com Страницы: 28
Yakima SideWinder Installation Instructions And Owner'S Manual preview
SideWinder
Бренд: Yakima Страницы: 8
B-Speech Pago INBTHF020 User Manual preview
Pago INBTHF020
Бренд: B-Speech Страницы: 24
Curt Manufacturing 31048 Installation Instructions Manual preview
31048
Бренд: Curt Manufacturing Страницы: 6
Volvo 2004 V70 (Swedish) Användarmanual preview
2004 V70
Бренд: Volvo Страницы: 188
IBASE Technology MPT-3000V User Manual preview
MPT-3000V
Бренд: IBASE Technology Страницы: 100
Modifry Products S2000 Windscreen Camera Mount Quick Start Manual preview
S2000 Windscreen Camera Mount
Бренд: Modifry Products Страницы: 2
Enduro autoSteady AS101 User Manual preview
autoSteady AS101
Бренд: Enduro Страницы: 48
GMC 2010 Tahoe Owner'S Manual preview
2010 Tahoe
Бренд: GMC Страницы: 120
Prime Tech H-066 User Manual preview
H-066
Бренд: Prime Tech Страницы: 6
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Бренд: Acura Страницы: 6
Air Lift 88365 Installation Manual preview
88365
Бренд: Air Lift Страницы: 28
Dolphin DAS400 Owner'S Manual preview
DAS400
Бренд: Dolphin Страницы: 16
Rugged Ridge 11232.20 Quick Start Manual preview
11232.20
Бренд: Rugged Ridge Страницы: 2
r.LiNK RL2-NBT Manual preview
RL2-NBT
Бренд: r.LiNK Страницы: 20
Saab 32000574 Installation Instructions Manual preview
32000574
Бренд: Saab Страницы: 9
Dodge Charger SRT 392 2017 Operating Information Manual preview
Charger SRT 392 2017
Бренд: Dodge Страницы: 576
Lexus LS 500h 2022 Owner'S Manual, Quick Manual preview
LS 500h 2022
Бренд: Lexus Страницы: 108

Бренды по названию

Популярные бренды

Загрузить еще бренды