manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

DTC P1260 [MZI-3.5] 

DTC P1260 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

 

DIAGNOSTIC PROCEDURE 

DTC P1260 (MZI-3.5) DIAGNOSTIC PROCEDURE

 

6

VERIFY TROUBLESHOOTING OF 
DTC P115E HAS BEEN 

COMPLETED

 

z

Verify that all disconnected 

connectors reconnected.  

z

Turn the ignition switch to the ON 
position (Engine off).  

z

Clear the DTC from the PCM 

memory using the M-MDS.  

z

Start the engine and run it at idle.  

z

Retrieve DTCs using the M-MDS. 

z

Is the PENDING CODE for this 
DTC present?  

Yes

Replace the PCM, then go to the next step.
(see 

PCM 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

No

Go to the next step.

7

VERIFY AFTER REPAIR 
PROCEDURE

 

z

Perform "AFTER REPAIR 

PROCEDURE". 

(See 

AFTER REPAIR 

PROCEDURE [MZI-3.5]

.) 

z

Are any DTC present?  

Yes

Go to the applicable DTC inspection. 
(See 

DTC TABLE [MZI-3.5]

.)

No

Troubleshooting completed.

DTC P1260

Theft detected, vehicle immobilized

DETECTION 

CONDITION

 

Indicates that the PATS determined a theft condition existed and the engine is 

disabled. This DTC is a good indicator to check the PATS for DTCs.

POSSIBLE CAUSE

 

z

Previous theft condition  

z

Anti-theft system failure Theft indicator flashing rapidly or on solid when 
the ignition switch is in the ON position.  

z

Check the anti-theft system for DTCs.  

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA 
HAS BEEN RECORDED

 

Yes

Go to the next step.

No

Record FREEZE FRAME DATA on the 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:36 AM

Page 345 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Fass Titanium Series Installation Manual preview
Titanium Series
Бренд: Fass Страницы: 13
Harmar Mobility AL001 Installation And Owner'S Manual preview
AL001
Бренд: Harmar Mobility Страницы: 10
Jeep Wrangler 2011 Owner'S Manual preview
Wrangler 2011
Бренд: Jeep Страницы: 603
Jeep Patriot 2011 User Manual preview
Patriot 2011
Бренд: Jeep Страницы: 80
Camcar 40061 Fe Mounting Instructions preview
40061 Fe
Бренд: Camcar Страницы: 2
PAC GM1A-R Quick Start Manual preview
GM1A-R
Бренд: PAC Страницы: 4
Cadillac Escalade ESV 2014 Owner'S Manual preview
Escalade ESV 2014
Бренд: Cadillac Страницы: 508
Hama Liberty III Quick Start Manual preview
Liberty III
Бренд: Hama Страницы: 2
Würth 071554055 User Instructions preview
071554055
Бренд: Würth Страницы: 36
Honda 2010 Civic Sedan Owner'S Manual preview
2010 Civic Sedan
Бренд: Honda Страницы: 390
Voxoa MCU-20A(P40) User Manual preview
MCU-20A(P40)
Бренд: Voxoa Страницы: 48
AEM 30-3500 Instruction Manual preview
30-3500
Бренд: AEM Страницы: 27
E&G Classics 1409-0102-10 Installation Instructions preview
1409-0102-10
Бренд: E&G Classics Страницы: 3
GMC 2013 GMC Savana Owner'S Manual preview
2013 GMC Savana
Бренд: GMC Страницы: 398
Quadratec 11113.1435 Quick Start Manual preview
11113.1435
Бренд: Quadratec Страницы: 14
Saab 32 025 603 Installation Instructions Manual preview
32 025 603
Бренд: Saab Страницы: 15
Curtis 1POLXP1000RP Installation & Owner'S Manual preview
1POLXP1000RP
Бренд: Curtis Страницы: 6
Dakota Digital CRS-3000-3 Manual preview
CRS-3000-3
Бренд: Dakota Digital Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды