manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

5. Using a straightedge, align the oil pan flush with the rear of the cylinder block at the two areas as shown. 

Fig. 18: Aligning Oil Pan Flush With Rear Of Cylinder Block

 

Courtesy of MAZDA MOTORS CORP.

 

6. Tighten the bolts in the order shown in the figure. 

Tightening torque

  

Bolt A: 18.5-21.5 N.m {1.89-2.19 kgf.m, 13.7-15.8 ft.lbf}

  

Bolt B: 8.5-11.5 N.m {87-117 kgf.cm, 76-101 in.lbf}

  

Fig. 19: Identifying Oil Pan Bolts With Tightning Sequence

 

Courtesy of MAZDA MOTORS CORP.

 

OIL PUMP REMOVAL/INSTALLATION [MZI-3.5] 

WARNING:

z

Fuel vapor Is hazardous. It can very easily ignite, causing serious 

injury and damage. Always keep sparks and flames away from fuel.  

z

Fuel line spills and leakage are dangerous. Fuel can ignite and cause 
serious injures or death and damage. Fuel can also irritate skin and, 

eyes. To prevent this, always complete the "Fuel Line Safety 

Procedure". (see BEFORE REPAIR PROCEDURE [MZI-3.5] .)  

z

Continuous exposure to USED engine oil has caused skin cancer in 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE Lubrication (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:32:53 AM

Page 14 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Hama Cup holder Operating Instruction preview
Cup holder
Бренд: Hama Страницы: 2
Abarth 124 SPIDER Service And Warranty Handbook preview
124 SPIDER
Бренд: Abarth Страницы: 36
LAS BC260 Operating Instructions Manual preview
BC260
Бренд: LAS Страницы: 44
LAS 11807 Operating Instructions Manual preview
11807
Бренд: LAS Страницы: 24
K&M 8494 Installation Manual preview
8494
Бренд: K&M Страницы: 3
Saleen 10-8002-C11998B Installation Manual preview
10-8002-C11998B
Бренд: Saleen Страницы: 12
Buick 2013 Buick Verano Manual preview
2013 Buick Verano
Бренд: Buick Страницы: 5
Camcar 40108 Mounting Instructions preview
40108
Бренд: Camcar Страницы: 6
ABL eMH3 Quick Start Manual preview
eMH3
Бренд: ABL Страницы: 4
AutoWatch 457 Rli Wiring Diagram preview
457 Rli
Бренд: AutoWatch Страницы: 4
Raytel LLC TellPhone 4200 Installation Instructions & Operating Manual preview
TellPhone 4200
Бренд: Raytel LLC Страницы: 40
Acura 2006 TSX Owner'S Manual preview
2006 TSX
Бренд: Acura Страницы: 2
Renault Lodgy 2017 Driver'S Handbook Manual preview
Lodgy 2017
Бренд: Renault Страницы: 238
WABCO TP19108 Installation Manual preview
TP19108
Бренд: WABCO Страницы: 32
Actia SmarTach Manual preview
SmarTach
Бренд: Actia Страницы: 102
Metra Electronics 99-7860 Installation Instructions preview
99-7860
Бренд: Metra Electronics Страницы: 5
Renkforce RF-4743771 Operating Instructions preview
RF-4743771
Бренд: Renkforce Страницы: 4
UAZ 2001 ???-3741 Instruction Manual preview
2001 ???-3741
Бренд: UAZ Страницы: 112

Бренды по названию

Популярные бренды

Загрузить еще бренды