Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 619

Страница: 619 / 1056

availability.

Is any related Service Bulletins

available?

Go to the next step.

INSPECT CRUISE CONTROL
SWITCH CONNECTOR FOR POOR

CONNECTION

Turn the ignition switch to off.

Disconnect the cruise control
switch connector.

Inspect for poor connection (such
as damaged/pulled-out pins,

corrosion).

Are there any malfunction?

Yes

Repair or replace suspected part, then go to
Step 9.

Go to the next step.

INSPECT CRUISE CONTROL
SWITCH CIRCUIT FOR SHORT TO

POWER SUPPLY

Turn the ignition switch to the ON

position (Engine off).

Measure the voltage between the
following terminals:

{

Cruise control switch

terminal B and body ground

{

Cruise control switch
terminal C and body ground

Are there voltage B+?

Yes

Repair or replace suspected part, then go to
Step 9.

Go to the next step.

INSPECT CRUISE CONTROL

SWITCH CIRCUIT FOR SHORT TO
GROUND

Turn the ignition switch off.

Inspect for continuity between the
following terminals:

{

Cruise control switch

terminal B and body ground

{

Cruise control switch
terminal C and body ground

Are there continuity?

Yes

Repair or replace suspected part, then go to

Step 9.

Go to the next step.

INSPECT PCM CONNECTOR FOR
POOR CONNECTION

Turn the ignition switch off.

Yes

Repair or replace suspected part, then go to
Step 9.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:34 AM

Page 272

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды