Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 336 | Manualshive

Страница: 336 / 1056

background image

10.7-24.5 N.m {1.1-2.4 kgf.m, 7.9-18.0 ft.lbf}

14. Install the fan control module No.2 (Dual fan control module) (see

FAN MOTOR

REMOVAL/INSTALLATION [MZI-3.5]

.)

15. Connect the negative battery cable.
16. Start the engine and confirm that there is no oil leakage.

z

If there is oil leakage, repair or replace the applicable part.

17. Install the engine cover.

Fig. 4: Applying Silicone Sealant To Oil Pressure Switch Threads

Courtesy of MAZDA MOTORS CORP.

OIL FILTER REPLACEMENT [MZI-3.5]

1. Remove the oil filter using a oil filter wrench.
2. Use a clean rag to wipe off the mounting surface on the oil filter adapter and the oil filter.
3. Apply clean engine oil to the O-ring of a new oil filter.
4. Install the oil filter until the O-ring contacts the sealing surface.
5. Tighten the oil filter 3/4 turns by hand.

WARNING:

z

Hot engines and engine oil can cause severe burns. Turn off the
engine and wait until it and the engine oil have cooled.

z

A vehicle that is lifted but not securely supported on safety stands is

dangerous. It can slip or fall, causing death or serious injury. Never

work around or under a lifted vehicle if it is not securely supported
on safety stands.

z

Continuous exposure to USED engine oil has caused skin cancer in

laboratory mice. Protect your skin by washing with soap and water

immediately after working with engine oil.

CAUTION:

z

If engine oil is spilled on the exhaust system, wipe it off completely. If
you fail to wipe the spilled engine oil, it will produce fumes because

of the heat.

2007 Mazda CX-9 Grand Touring

2007 ENGINE Lubrication (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:32:53 AM

Page 5

© 2005 Mitchell Repair Information Company, LLC.

«
...
334
335
336
337
338
...
»

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Бренд: HALE Страницы: 44

Бренд: Zavoli Страницы: 26

Бренд: Honda Страницы: 73

Бренд: IAG Страницы: 3

Indigo MANZA QUADRAJET 90

Бренд: TATA Motors Страницы: 10

Бренд: Chariot Carriers Страницы: 3

1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28

Бренд: Havis-Shields Страницы: 3

Бренд: FALCON RIDGE Страницы: 8

Бренд: Scosche Страницы: 8

Бренд: Nav TV Страницы: 4

Бренд: Easee Страницы: 12

Бренд: JANE Страницы: 58

Бренд: Cadillac Страницы: 20

DAF CHARGEMAX 90

Бренд: Paccar Страницы: 40

Бренд: AEM Страницы: 27

S90 - ACCESSORY PANEL

Бренд: Volvo Страницы: 166

Бренд: GReddy Страницы: 12

Бренд: Prorack Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды