Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 203

Страница: 203 / 1056

Fig. 13: Identifying Valve Clearance Adjustment Locations

Courtesy of MAZDA MOTORS CORP.

3. Mark the crank pulley and engine front cover as shown in the figure.
4. Rotate the crankshaft clockwise

360°

so that the No.5 cylinder is at TDC of the compression stroke.

5. Measure the valve clearance of location B shown in the figure.

If it is not within the specification, replace the tappet and adjust the valve clearance to the
median value of the standard.

Standard valve clearance [Engine cold]

IN: 0.150-0.250 mm {0.00591-0.00984 in}

EX: 0.300-0.400 mm {0.0119-0.0157 in}

13. Install in the reverse order of removal.

NOTE:

Make sure to note down the measured values for choosing the
suitable replacement tappets.

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:27 AM

Page 12

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды