manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

DTC P0148 [MZI-3.5] 

DTC P0148 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

 

z

Disconnect all the PCM 

connectors.  

z

Visually inspect for: 

{

Pushed out pins  

{

Corrosion  

z

Connect all the PCM connectors 

and verify that they seat correctly. 

z

Retrieve DTCs using the M-MDS. 

z

Is the PENDING CODE for this 
DTC present?  

No

The system is correctly. Go to the next 
step.

12

VERIFY TROUBLESHOOTING OF 

MISFIRE DTC HAS BEEN 
COMPLETED

 

z

Verify that all disconnected 
connectors are reconnected.  

z

Turn the ignition switch to the ON 

position (Engine off).  

z

Clear the DTC from the PCM 
memory using the M-MDS.  

z

Retrieve DTCs using the M-MDS. 

z

Is the PENDING CODE for this 

DTC present?  

Yes

Replace PCM, then go to the next step. 

(see 

PCM 

REMOVAL/INSTALLATION [MZI-

3.5]

 .)

No

Go to the next step.

13

VERIFY AFTER REPAIR 

PROCEDURE

 

z

Perform "AFTER REPAIR 
PROCEDURE". 

(See 

AFTER REPAIR 

PROCEDURE [MZI-3.5]

.) 

z

Are any DTC present?  

Yes

Go to the applicable DTC inspection. 

(See 

DTC TABLE [MZI-3.5]

.)

No

Troubleshooting completed.

DTC P0148

Fuel delivery error

DETECTION 
CONDITION

 

z

At least 1 bank is lean at wide open throttle (WOT).  

POSSIBLE CAUSE

 

z

Severely restricted fuel filter  

z

Severely restricted fuel supply line  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:30 AM

Page 104 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Davis Instruments 8127 Installation Instructions Manual preview
8127
Бренд: Davis Instruments Страницы: 16
VEAP SHIELD UNITED FT Series Mounting Instruction preview
FT Series
Бренд: VEAP SHIELD UNITED Страницы: 3
Chevrolet 2013 Spark Owner'S Manual preview
2013 Spark
Бренд: Chevrolet Страницы: 356
Ford Zephyr 2007 Owner'S Manual preview
Zephyr 2007
Бренд: Ford Страницы: 272
Pontiac 2004 Sunfire Owner'S Manual preview
2004 Sunfire
Бренд: Pontiac Страницы: 376
Jeep COMPASS 2018 Owner'S Manual preview
COMPASS 2018
Бренд: Jeep Страницы: 712
Gator HUDGPS1 Quick Start Manual preview
HUDGPS1
Бренд: Gator Страницы: 2
Prorack K544 Fitting Instructions Manual preview
K544
Бренд: Prorack Страницы: 20
Cadillac 2004 ESCALADE Customer Convenience/Personalization Manual preview
2004 ESCALADE
Бренд: Cadillac Страницы: 20
Mercedes-Benz E55AMG Service Manual preview
E55AMG
Бренд: Mercedes-Benz Страницы: 39
Oldsmobile 2000 Oldsmobile Intrigue Owner'S Manual preview
2000 Oldsmobile Intrigue
Бренд: Oldsmobile Страницы: 348
Mitsubishi Fuso FK 2010 Owner'S Manual preview
Fuso FK 2010
Бренд: Mitsubishi Страницы: 362
GYS 029422 Manual preview
029422
Бренд: GYS Страницы: 32
Renault CAPTUR 2019 Vehicle Instruction Card preview
CAPTUR 2019
Бренд: Renault Страницы: 11
iSimple IS7705 Installation & Operation Manual preview
IS7705
Бренд: iSimple Страницы: 8
K&N Engineering Filtercharger 57-9004 Installation Manual preview
Filtercharger 57-9004
Бренд: K&N Engineering Страницы: 4
Honda Element 2004 Owner'S Manual preview
Element 2004
Бренд: Honda Страницы: 219
EUFAB 16559 Operating Instructions Manual preview
16559
Бренд: EUFAB Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды