Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 201

Страница: 201 / 1056

Courtesy of MAZDA MOTORS CORP.

6. Turn the drive belt auto tensioner pulley by hand and verify that it rotates smoothly.

Replace the drive belt auto tensioner if necessary.

Tightening torque

8.9-12.1 N.m {91-123 kgf.cm, 79-107 in.lbf}

7. Install in the reverse order of removal.

Fig. 11: Rotating Drive Belt Auto Tensioner Pulley

Courtesy of MAZDA MOTORS CORP.

VALVE CLEARANCE INSPECTION/ADJUSTMENT [MZI-3.5]

VALVE CLEARANCE INSPECTION

1. Disconnect the negative battery cable.
2. Remove the engine cover. (See

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.5]

3. Remove the ventilation hose.
4. Remove the resonance chamber. (see

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.5]

5. Remove the dynamic chamber and throttle body as a single unit. (see

INTAKE-AIR SYSTEM

REMOVAL/INSTALLATION [MZI-3.5]

6. Disconnect the wiring harness.
7. Remove the ignition coils. (see

IGNITION COIL REMOVAL/INSTALLATION [MZI-3.5]

8. Remove the dipstick.
9. Remove the cylinder head cover. (See

TIMING CHAIN REMOVAL/INSTALLATION [MZI-3.5]

10. Remove the front wheel and tire (RH). (see

GENERAL PROCEDURES (SUSPENSION).

)

11. Remove the splash shield (RH).
12. Measure the valve clearance.

1. Rotate the crankshaft clockwise and verify that the timing mark of the intake side camshaft

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:27 AM

Page 10

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды