manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

3. Connect a battery charger to the battery and adjust the charging current as follows. 

Battery slow charge current

  

80D26L (55): 5.5-6.5 A

  

Battery quick charge current [30 min]

  

80D26L (55): 35 A

  

4. After the battery is recharged, verify that the voltage is within the specification and remains at the same 

value for 

1 h or more

 after the recharging has been completed. 

z

If not within the specification, replace the battery.  

Standard voltage

  

12.4 V or more

  

Fig. 4: Connecting Battery Charger To Battery

 

Courtesy of MAZDA MOTORS CORP.

 

GENERATOR REMOVAL/INSTALLATION [MZI-3.5] 

1. Disconnect the negative battery cable.  
2. Drain the engine coolant. (see 

ENGINE COOLANT REPLACEMENT [MZI-3.5]

 .)  

3. Remove the air cleaner and fresh air duct component. (see 

INTAKE-AIR SYSTEM 

WARNING:

z

Remove and install all parts when the engine is cold, otherwise they 

can cause severe burns or serious injury.  

z

When the battery cables are connected, touching the vehicle body 
with generator terminal B will generate sparks. This can cause 

personal injury, fire, and damage to the electrical components. 

Always disconnect the negative battery cable before performing the 
following operation.  

 

2007 Mazda CX-9 Grand Touring 

2007 ELECTRICAL Charging System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:29:33 AM

Page 5 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

ZAPTEC Go Quick Manual preview
Go
Бренд: ZAPTEC Страницы: 64
ZAPTEC Go Installation Manual preview
Go
Бренд: ZAPTEC Страницы: 24
Qube AP1 Supplemental Instructions preview
AP1
Бренд: Qube Страницы: 19
Cadillac 2000 Warranty And Owner Assistance Information preview
2000
Бренд: Cadillac Страницы: 32
Yakima K618 Instructions Manual preview
K618
Бренд: Yakima Страницы: 11
Alpine eX-10 Owner'S Manual preview
eX-10
Бренд: Alpine Страницы: 69
Allen Sports S302 Instructions preview
S302
Бренд: Allen Sports Страницы: 2
Mobile Create MCM3 Instruction Manual preview
MCM3
Бренд: Mobile Create Страницы: 15
Atwood Lippert Components LEVELEGS MPD 66385 Manual preview
Lippert Components LEVELEGS MPD 66385
Бренд: Atwood Страницы: 6
BMW 65 41 2 152 528 Installation Instructions Manual preview
65 41 2 152 528
Бренд: BMW Страницы: 21
Quadratec 12226.3011 Installation Manual preview
12226.3011
Бренд: Quadratec Страницы: 8
Whispbar K604W Fitting Instructions Manual preview
K604W
Бренд: Whispbar Страницы: 15
Safe Fleet PRIME DESIGN VRR-E-PM21 Assembly Instructions Manual preview
PRIME DESIGN VRR-E-PM21
Бренд: Safe Fleet Страницы: 12
Q Mobility Group Q Access Alpha GSE 2023 Installation Manual preview
Q Access Alpha GSE 2023
Бренд: Q Mobility Group Страницы: 9
Porsche 01-B Web Application Manual preview
01-B
Бренд: Porsche Страницы: 313
Hella AREIA 7040 Installation Instructions Manual preview
AREIA 7040
Бренд: Hella Страницы: 21
Cadillac 1999 Escalade Owner'S Manual preview
1999 Escalade
Бренд: Cadillac Страницы: 352
ULTIMATE SPEED 91449 Operation And Safety Notes preview
91449
Бренд: ULTIMATE SPEED Страницы: 34

Бренды по названию

Популярные бренды

Загрузить еще бренды