manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

4. Remove the HO2S (RH) using the 

SST.

 

5. Install in the reverse order of removal. 

Fig. 23: View Of RH HO2S With Torque Specifications

 

Courtesy of MAZDA MOTORS CORP.

 

FRONT HEATED OXYGEN SENSOR (HO2S) INSPECTION [MZI-3.5] 

FRONT HEATED OXYGEN SENSOR (HO2S) VOLTAGE INSPECTION 

1. Warm up the engine to normal operating temperature.  
2. Using the M-MDS, monitor the following: 

{

Vehicle speed (PID: VSS)  

{

Engine speed (PID: RPM)  

{

Front HO2S voltage (PID: O2S11, O2S21)  

3. Drive the vehicle and decelerate the engine speed by releasing the accelerator pedal fully when the engine 

speed is 

3,000 rpm or more.

  

4. Verify that the front HO2S outputs a voltage of 

0.6 V or more,

 one time or more, then verify that the 

front HO2S voltage (PID: O2S11, O2S21) is 

0.3 V is or less

while decelerating as shown in the figure. 

NOTE:

z

Apply a light coat of anti-seize lubricant to the threads of the HO2S. 

NOTE:

z

Before performing the following inspection, make sure to follow the 

procedure as indicated in the troubleshooting flowchart. (see HOW TO 
USE THIS MANUAL .)  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Control System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:25:31 AM

Page 26 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Monacor CARPOWER CAP-12XHQ Manual preview
CARPOWER CAP-12XHQ
Бренд: Monacor Страницы: 5
Jeep Grand Cherokee WK2 Owner'S Manual preview
Grand Cherokee WK2
Бренд: Jeep Страницы: 338
PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Бренд: PUTCO Страницы: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Бренд: Westfalia Страницы: 18
Waeco MagicComfort MSH200 Installation And Operating Instructions Manual preview
MagicComfort MSH200
Бренд: Waeco Страницы: 108
Tusk RL-HM018R Installation Instructions And Information Manual preview
RL-HM018R
Бренд: Tusk Страницы: 2
Yakima StickUp Installation Instructions Manual preview
StickUp
Бренд: Yakima Страницы: 21
Van Guard VG273 Fitting Instructions preview
VG273
Бренд: Van Guard Страницы: 3
Cadillac 1993 Seville Owners Literature preview
1993 Seville
Бренд: Cadillac Страницы: 407
STO N SHO SNS135a Installation Procedures Manual preview
SNS135a
Бренд: STO N SHO Страницы: 7
Yakima Prorack K436 Fitting Instructions Manual preview
Prorack K436
Бренд: Yakima Страницы: 13
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Бренд: Saturn Страницы: 440
Edelbrock Honda XR400 Instruction Supplement preview
Honda XR400
Бренд: Edelbrock Страницы: 2
Hudson Super Six 1916 Reference Book preview
Super Six 1916
Бренд: Hudson Страницы: 77
Audiovox Auto Security AA-9103N Installation Manual preview
Auto Security AA-9103N
Бренд: Audiovox Страницы: 1
ULTIMATE SPEED UKLL 5 A1 Operating Instructions Manual preview
UKLL 5 A1
Бренд: ULTIMATE SPEED Страницы: 132
Mini COOPER Convertible Owner'S Manual preview
COOPER Convertible
Бренд: Mini Страницы: 168
Proxel EPS-DUAL Installation Instructions & User Manual preview
EPS-DUAL
Бренд: Proxel Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды