manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

DIAGNOSTIC PROCEDURE 

DIAGNOSTIC PROCEDURE

 

z

Improper tension of drive belt  

z

Drive belt damage  

STEP INSPECTION

RESULTS ACTION

1

Inspect the following: 

z

Engine coolant level  

z

Coolant leakage  

z

Water and anti-freeze mixture  

z

Radiator condition  

z

Collapsed or restricted radiator 

hoses  

z

Radiator pressure cap  

z

Overflow system  

z

Fan rotational direction  

z

Fuses  

 

Are all items normal?

Yes

Go to the next step.

No

Service if necessary. 

Repeat Step 1.

2

Connect the M-MDS to the DLC-2. 
Turn the ignition switch to the ON position 

(Engine off). 
Retrieve any DTCs. 

Are there any DTCs displayed?

Yes

DTC is displayed:

  

Go to the appropriate DTC 

inspection. 
(see 

DTC TABLE [MZI-3.5]

 .)

No

No DTC is displayed:

  

Go to the next step.

3

Start the engine and idle it. 

Turn the A/C switch on and set blower fan 
to any speed. 

Does the A/C compressor engage?

Yes

Go to Step 5.

No

Inspect for the following and repair 

or replace if necessary: 

z

Refrigerant charging amount  

z

Open circuit in wiring harness 

between A/C relay and PCM 
terminal 1N  

z

Seized A/C magnetic clutch  

z

A/C magnetic clutch 

malfunction  

 

If all items are normal, go to the next 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:37 AM

Page 68 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

A-Tach Mounts 50131 Instructions preview
50131
Бренд: A-Tach Mounts Страницы: 2
RaceChip Pro 2 Installation Manual preview
Pro 2
Бренд: RaceChip Страницы: 12
RAM Commercial PROMASTER 2020 Quick Reference Manual preview
PROMASTER 2020
Бренд: RAM Commercial Страницы: 12
Yamaha Yamaha Rhino 660 Instruction Supplement preview
Yamaha Rhino 660
Бренд: Yamaha Страницы: 3
Air Lift WirelessAIR 73000EZ Manual preview
WirelessAIR 73000EZ
Бренд: Air Lift Страницы: 12
K&M MILSCO KIT# C746700 Installation Manual preview
MILSCO KIT# C746700
Бренд: K&M Страницы: 2
Car-Interface CI-RL4-NAC12 Manual preview
CI-RL4-NAC12
Бренд: Car-Interface Страницы: 25
Thule 2 Bike Carrier 977 Instructions Manual preview
2 Bike Carrier 977
Бренд: Thule Страницы: 6
SCC Quik Grip Installation And Removal Instructions preview
Quik Grip
Бренд: SCC Страницы: 4
Simplicity 1694286 Installation Instructions Manual preview
1694286
Бренд: Simplicity Страницы: 10
Subaru 1998 Forester Owner'S Manual preview
1998 Forester
Бренд: Subaru Страницы: 298
Cadillac GMC Yukon Denali 2005 Owner'S Manual preview
GMC Yukon Denali 2005
Бренд: Cadillac Страницы: 456
Saab 900 5 Speed Technical Training Manual preview
900 5 Speed
Бренд: Saab Страницы: 63
R&G LP0291BK Fitting Instructions Manual preview
LP0291BK
Бренд: R&G Страницы: 20
Whispbar S17W Fitting Instructions Manual preview
S17W
Бренд: Whispbar Страницы: 70
Racelogic Speed & Route Profiler Manual preview
Speed & Route Profiler
Бренд: Racelogic Страницы: 24
Brink 4698 Fitting Instructions Manual preview
4698
Бренд: Brink Страницы: 26
Mitsubishi Fuso FK 2010 Owner'S Manual preview
Fuso FK 2010
Бренд: Mitsubishi Страницы: 362

Бренды по названию

Популярные бренды

Загрузить еще бренды