manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

10

INSPECT A/C RELAY

 

z

Inspect A/C relay. 

(see 

RELAY INSPECTION

 .) 

z

Is A/C relay normal?  

Yes

Go to the next step.

No

Replace the A/C relay. Start the engine. 

Turn on the A/C switch. Wait for 

15 s

 . 

Turn off the A/C switch, then go to Step 

12.

11

INSPECT FOR CORRECT PCM 
OPERATION

 

z

Disconnect all the PCM 
connectors.  

z

Visually inspect for: 

{

Pushed out pins  

{

Corrosion  

z

Connect all the PCM connectors 

and verify that they seat correctly. 

z

Retrieve DTCs using the M-MDS. 

z

Is the PENDING CODE for this 
DTC present?  

Yes

Go to the next step.

No

The system is correctly. Go to the next 

step.

12

VERIFY TROUBLESHOOTING OF 
DTC P0645 HAS BEEN 

COMPLETED

 

z

Verify that all disconnected 
connectors reconnected.  

z

Clear the DTC from the PCM 

memory using the M-MDS.  

z

Perform the "KOEO or KOER 
self-test" using the M-MDS. 

(See 

KOEO/KOER SELF TEST 

[MZI-35]

) 

z

Is the PENDING CODE for the 

DTC present?  

Yes

Replace the PCM, then go to the next step.
(see 

PCM 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

No

Go to the next step.

13

VERIFY AFTER REPAIR 

PROCEDURE

 

z

Perform the "AFTER REPAIR 
PROCEDURE". 

(See 

AFTER REPAIR 

PROCEDURE [MZI-3.5]

.) 

Yes

Go to the applicable DTC inspection. 

(See 

DTC TABLE [MZI-3.5]

.)

No

Troubleshooting completed.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:35 AM

Page 323 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Acdeos AXS FL Installation Instruction preview
AXS FL
Бренд: Acdeos Страницы: 7
Jeep Wrangler 2011 Owner'S Manual preview
Wrangler 2011
Бренд: Jeep Страницы: 603
Jeep Patriot 2011 User Manual preview
Patriot 2011
Бренд: Jeep Страницы: 80
Kia 2016 Cadenza Owner'S Manual preview
2016 Cadenza
Бренд: Kia Страницы: 419
Rightline Gear Car Top Duffle Bag Setup Manual preview
Car Top Duffle Bag
Бренд: Rightline Gear Страницы: 2
Thule 1308 Instructions Manual preview
1308
Бренд: Thule Страницы: 8
VDO DLD Wide Range II Installation Instructions Manual preview
DLD Wide Range II
Бренд: VDO Страницы: 84
Wagan TravelCharge Companion GO-Plus User Manual preview
TravelCharge Companion GO-Plus
Бренд: Wagan Страницы: 3
TATA Motors Tata Indigo Diesel Owner'S Manual & Service Book preview
Tata Indigo Diesel
Бренд: TATA Motors Страницы: 190
Safe Fleet Prime Design HBR-E-FT33B Assembly Instructions Manual preview
Prime Design HBR-E-FT33B
Бренд: Safe Fleet Страницы: 12
Easee Home Wallbox Installation Instructions Manual preview
Home Wallbox
Бренд: Easee Страницы: 12
Hank HKWP1100-10Q User Quick Manual preview
HKWP1100-10Q
Бренд: Hank Страницы: 2
Valeo Park Vision VAL632210 Instruction Manual preview
Park Vision VAL632210
Бренд: Valeo Страницы: 25
Warn 70948 Installation Instructions preview
70948
Бренд: Warn Страницы: 5
v.link NAL-PC-HSD Manual preview
NAL-PC-HSD
Бренд: v.link Страницы: 21
Cadillac ESCALADE ESV 2005 Owner'S Manual preview
ESCALADE ESV 2005
Бренд: Cadillac Страницы: 482
curt CM-58967 Installation Manual preview
CM-58967
Бренд: curt Страницы: 4
CITROËN Jumpy Miltispace Owner'S Handbook Manual preview
Jumpy Miltispace
Бренд: CITROËN Страницы: 164

Бренды по названию

Популярные бренды

Загрузить еще бренды