manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

z

Inspect for continuity between 

throttle body connector terminal C 

(wiring harness-side) and PCM 
terminal 2AD (wiring harness-

side).  

z

Is there continuity?  

No

Repair or replace suspected part, then go to 
Step 9.

7

INSPECT TP GROUND CIRCUIT 
FOR OPEN CIRCUIT

 

z

Turn the ignition switch off.  

z

Verify the continuity between TP 
sensor terminal E and body 

ground.  

z

Is the continuity?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go to 

Step 9.

8

INSPECT TP SENSOR NO.2

 

z

Inspect the TP sensor No.2. 

(see 

THROTTLE POSITION 

(TP) SENSOR INSPECTION 
[MZI-3.5].

 ) 

z

Is there any malfunction?  

Yes

Replace the throttle body, then go to the 
next step.

No

Go to the next step.

9

VERIFY TROUBLESHOOTING OF 
DTC P0222 HAS BEEN 

COMPLETED

 

z

Make sure to reconnect all 
disconnected connectors.  

z

Clear the DTC from the PCM 
memory using the M-MDS.  

z

Start the engine.  

z

Perform the "KOEO/KOER self-

test". 

(See 

KOEO/KOER SELF TEST 

[MZI-3.5]

.) 

z

Is same DTC present?  

Yes

Replace the PCM, then go to the next step.
(see 

PCM 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

No

Go to the next step.

10

VERIFY AFTER REPAIR 
PROCEDURE

 

z

Perform the "AFTER REPAIR 
PROCEDURE". 

Yes

Go to the applicable DTC inspection. 
(See 

DTC TABLE [MZI-3.5]

.)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:31 AM

Page 142 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Saab 99 Important Operatlng, Safety And Maintenance Instructions preview
99
Бренд: Saab Страницы: 75
VEAP SHIELD UNITED FT Series Mounting Instruction preview
FT Series
Бренд: VEAP SHIELD UNITED Страницы: 3
Kathrein DDA Series User Manual preview
DDA Series
Бренд: Kathrein Страницы: 7
Napoli NPL-TV 7874 DIGITAL Instruction Manual preview
NPL-TV 7874 DIGITAL
Бренд: Napoli Страницы: 20
Roav R5141 Owner'S Manual preview
R5141
Бренд: Roav Страницы: 10
Alfa Romeo FIX&GO automatic Manual preview
FIX&GO automatic
Бренд: Alfa Romeo Страницы: 40
muth signal mirror Instalation Instructions preview
signal mirror
Бренд: muth Страницы: 10
Cadillac 1993 Seville Owners Literature preview
1993 Seville
Бренд: Cadillac Страницы: 407
Caltrend BM110 Installation Instructions preview
BM110
Бренд: Caltrend Страницы: 2
Advanced ICE 1296-1 Manual preview
1296-1
Бренд: Advanced ICE Страницы: 4
Dakota Digital LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne... Installation Instructions preview
LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...
Бренд: Dakota Digital Страницы: 3
Ecco 5545A Installation And Operating Instructions Manual preview
5545A
Бренд: Ecco Страницы: 12
CTEK D250S Dual Manual preview
D250S Dual
Бренд: CTEK Страницы: 84
mtf TRANSPORT SYSTEM BackPower Manual preview
BackPower
Бренд: mtf TRANSPORT SYSTEM Страницы: 9
Paccar DAF CHARGEMAX 90 User Manual preview
DAF CHARGEMAX 90
Бренд: Paccar Страницы: 40
HAKR TRIP 3 Instructions For Use Manual preview
TRIP 3
Бренд: HAKR Страницы: 9
VP Autoparts 419420 Installation preview
419420
Бренд: VP Autoparts Страницы: 2
Mazda 2006 MPV Quick Tips preview
2006 MPV
Бренд: Mazda Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды