manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

Fig. 9: Verifying Drive Belt Is Fully Attached To Pulleys

 

Courtesy of MAZDA MOTORS CORP.

 

4. Install the generator and A/C drive belt. (See 

GENERATOR AND A/C DRIVE BELT

.)  

5. Verify that the drive belt auto tensioner indicator mark does not exceeds the maximum belt length. (See 

DRIVE BELT INSPECTION [MZI-3.5]

.) 

z

If it exceeds the maximum belt length, replace the generator and A/C drive belt.  

DRIVE BELT AUTO TENSIONER INSPECTION [MZI-3.5] 

1. Remove the engine cover. (See 

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.5]

.)  

2. Remove the front wheel and tire (RH). (see 

GENERAL PROCEDURES (SUSPENSION).

 )  

3. Remove the splash shield (RH).  
4. Remove the generator and A/C drive belt. (See 

DRIVE BELT REMOVAL/INSTALLATION [MZI-

3.5]

.)  

5. Verify that the drive belt auto tensioner moves smoothly in the operational direction. 

z

Replace the drive belt auto tensioner if necessary. 

Tightening torque

  

8.9-12.1 N.m {91-123 kgf.cm, 79-107 in.lbf}

  

Fig. 10: Verifying Drive Belt Auto Tensioner Moves Smoothly

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE Mechanical (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:19:27 AM

Page 9 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

LAS BC260 Operating Instructions Manual preview
BC260
Бренд: LAS Страницы: 44
LAS 11807 Operating Instructions Manual preview
11807
Бренд: LAS Страницы: 24
iDataLink BLADE-AL(TB)-TL2 Install Manual preview
BLADE-AL(TB)-TL2
Бренд: iDataLink Страницы: 9
Magneti Marelli BCF184 Installation Instructions preview
BCF184
Бренд: Magneti Marelli Страницы: 2
Honda 08A28-0J6-800 Installation Instructions Manual preview
08A28-0J6-800
Бренд: Honda Страницы: 32
Whelen Engineering Company FastTrax FTF4 Installation Manual preview
FastTrax FTF4
Бренд: Whelen Engineering Company Страницы: 9
Kia CADENZA 2017 Features & Functions Manual preview
CADENZA 2017
Бренд: Kia Страницы: 58
Classic AutoAir Mustang 1969 Installation Manual preview
Mustang 1969
Бренд: Classic AutoAir Страницы: 44
Westin 33-1920 Instructions preview
33-1920
Бренд: Westin Страницы: 3
LaserLine 921K Operating Instructions preview
921K
Бренд: LaserLine Страницы: 4
TATA Motors Indigo Marina Owner'S Manual & Service Book preview
Indigo Marina
Бренд: TATA Motors Страницы: 146
Yakima SUPDawg Manual preview
SUPDawg
Бренд: Yakima Страницы: 10
Classic Accessories 80-485-142401-RT Instructions Manual preview
80-485-142401-RT
Бренд: Classic Accessories Страницы: 14
Volkswagen Passat 2011 Maintenance Manual preview
Passat 2011
Бренд: Volkswagen Страницы: 188
Chevrolet El Camino 1983 Owner'S Manual preview
El Camino 1983
Бренд: Chevrolet Страницы: 103
Peak PKC0BJ Owner'S Manual preview
PKC0BJ
Бренд: Peak Страницы: 8
Renault Kangoo Manual preview
Kangoo
Бренд: Renault Страницы: 239
Gold Lantern GL-VTMK20 Specifications preview
GL-VTMK20
Бренд: Gold Lantern Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды