Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 281

Страница: 281 / 1056

1. Disconnect the negative battery cable.
2. Remove the OCV. (See

OIL CONTROL VALVE (OCV) REMOVAL/INSTALLATION [MZI-3.5]

3. Verify that the spool valve in the OCV is in the maximum valve timing retard position as indicated in the

figure.

If not as specified, replace the OCV.

4. Verify that the battery is fully charged.

If not as specified, recharge the battery.

Fig. 143: Identifying Spool Valve

Courtesy of MAZDA MOTORS CORP.

5. Apply battery positive voltage between the OCV terminals and verify that the spool valve operates and

moves to the maximum valve timing advance position.

Fig. 144: Identifying OCV Connector Terminals

Courtesy of MAZDA MOTORS CORP.

If not as specified, replace the OCV.

NOTE:

When applying battery positive voltage between the OCV terminals,

the connection can be either of the following:

{

Positive battery cable to terminal A, Negative battery cable to

terminal B

{

Positive battery cable to terminal B, Negative battery cable to

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:28 AM

Page 90

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды