manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

DIAGNOSTIC PROCEDURE 

DIAGNOSTIC PROCEDURE

 

POSSIBLE CAUSE

 

z

Accelerator pedal position sensor or related circuit malfunction  

z

Accelerator pedal position sensor misadjustment  

z

TP sensor or related circuit malfunction  

z

MAF sensor or related circuit malfunction  

z

Brake switch or related circuit malfunction  

z

TR switch or related circuit malfunction  

z

Improper A/C magnetic clutch operation  

STEP INSPECTION

RESULTS ACTION

1

Does the engine idle roughly?

Yes

Go to symptom troubleshooting "No.8 

Engine runs rough/rolling idle". 
(See 

NO.8 ENGINE RUNS 

ROUGH/ROLLING IDLE [MZI-
3.5]

.)

No

Go to the next step.

2

Turn off the A/C switch and fan switch.

Does the A/C magnetic clutch engage?

Yes

Go to symptom troubleshooting 

"No.24 A/C is always on or A/C 

compressor runs continuously." 
(See 

NO.24 A/C IS ALWAYS ON 

OR A/C COMPRESSOR RUNS 
CONTINUOUSLY [MZI-3.5]

.)

No

Go to the next step.

3

Verify the following: 

z

Proper routing of and no damage 
to vacuum lines  

z

No air leakage from intake-air 

system  

 
Are all items normal?

Yes

Go to the next step.

No

Service if necessary. 

Repeat Step 3.

4

Connect the M-MDS to the DLC-2. 
Turn the ignition switch to the ON 

position (Engine off). 
Retrieve any DTCs. 

Are there any DTCs displayed?

Yes

DTC is displayed:

  

Go to the appropriate DTC inspection.

(see 

DTC TABLE [MZI-3.5]

 .)

No

No DTC is displayed:

  

Go to the next step.

5

Perform the electronic throttle control 

system operation inspection. 

(See 

ENGINE CONTROL SYSTEM 

OPERATION INSPECTION [MZI-

Yes

Go to the next step.

No

Repair or replace the malfunctioning 
part according to electronic throttle 

control system operation inspection 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:37 AM

Page 46 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Acdeos AXS FL Installation Instruction preview
AXS FL
Бренд: Acdeos Страницы: 7
Camoplast T4S User Manual preview
T4S
Бренд: Camoplast Страницы: 60
Feniex AM600 Instruction Manual preview
AM600
Бренд: Feniex Страницы: 6
Carefree Slideout Cover Service Manual preview
Slideout Cover
Бренд: Carefree Страницы: 12
Jeep Cherokee 16 1982 Technical & Service Manual preview
Cherokee 16 1982
Бренд: Jeep Страницы: 1311
Ultra-tow XTP Series Owner'S Manual preview
XTP Series
Бренд: Ultra-tow Страницы: 14
Mercedes-Benz 300D 2.5 1990 Owner'S Manual preview
300D 2.5 1990
Бренд: Mercedes-Benz Страницы: 121
Menabo BIKE PRO Fitting Instructions Manual preview
BIKE PRO
Бренд: Menabo Страницы: 8
Camtree G-51 Instruction Manual preview
G-51
Бренд: Camtree Страницы: 5
Cadillac XT4 2022 Convenience/Personalization Manual preview
XT4 2022
Бренд: Cadillac Страницы: 20
Pontiac 2006 Relay Getting To Know Manual preview
2006 Relay
Бренд: Pontiac Страницы: 20
Horn Tools HJIMRR02FIT Mounting Instructions preview
HJIMRR02FIT
Бренд: Horn Tools Страницы: 12
Oldsmobile 1994 Bravada Owner'S Manual preview
1994 Bravada
Бренд: Oldsmobile Страницы: 248
Volkswagen Zubehör 000 071 105 D Installation Instructions Manual preview
000 071 105 D
Бренд: Volkswagen Zubehör Страницы: 133
Westfalia 17 56 46 Instruction Manual preview
17 56 46
Бренд: Westfalia Страницы: 2
Stanley GLPS Instruction Manual preview
GLPS
Бренд: Stanley Страницы: 6
Macally MAGME User Manual preview
MAGME
Бренд: Macally Страницы: 10
Paser SKT 170 HYUNDAI Installation Manual preview
SKT 170 HYUNDAI
Бренд: Paser Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды