Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 444

Страница: 444 / 1056

Is the resistance less than 5 ohms?

INSPECT INTERNAL
RESISTANCE OF HO2S HEATER

Measure the resistance between

the suspect HO2S terminal A and
C at component side.

Is the resistance between 3-30

ohms?

Yes

Go to the next step.

Install a new HO2S. Then go to Step 17.

INSPECT HO2S HEATER CIRCUIT

FOR INTERNAL SHORT TO
SIGRTN OR GROUND

Measure the resistance between:

{

HO2S terminal A and D at

component side

{

HO2S terminal A at

component side and battery
negative terminal

Is the resistance more than 10

kilohms?

Yes

Go to the next step.

Replace the HO2S.
(see

FRONT HEATED OXYGEN

SENSOR (HO2S)
REMOVAL/INSTALLATION [MZI-

3.5].

)

(see

REAR HEATED OXYGEN

SENSOR (HO2S)
REMOVAL/INSTALLATION [MZI-

3.5].

)

Then go to Step 17.

INSPECT HO2S

For DTC P0133 Inspect the front

HO2S(RH)

For DTC P0139 Inspect the rear
HO2S(RH)

For DTC P0153 Inspect the front

HO2S(LH)

For DTC P0159 Inspect the rear
HO2S(LH)

(see

FRONT HEATED

OXYGEN SENSOR (HO2S)
INSPECTION [MZI-3.5].

)

(see

REAR HEATED OXYGEN

SENSOR (HO2S)

INSPECTION [MZI-3.5].

)

Is there any malfunction?

Yes

Replace the HO2S.
(see

FRONT HEATED OXYGEN

SENSOR (HO2S)
REMOVAL/INSTALLATION [MZI-

3.5].

)

(see

REAR HEATED OXYGEN

SENSOR (HO2S)
REMOVAL/INSTALLATION [MZI-

3.5].

)

Then go to Step 17.

Go to the next step.

INSPECT FOR CORRECT PCM

OPERATION

Yes

Go to the next step.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:30 AM

Page 97

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды