Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 747

Страница: 747 / 1056

Verify related Service Bulletins

and/or on-line repair information

availability.

Is any related Service Bulletins
available?

If the vehicle is not repaired, go to

the next step.

Go to the next step.

INSPECT MAP SENSOR

CONNECTOR FOR POOR
CONNECTION

Turn the ignition switch off.

Disconnect the MAF/IAT sensor
connector.

Inspect for poor connection (such

as damaged/pulled-out pins,
corrosion).

Are there any malfunction?

Yes

Repair or replace suspected part, then go to

Step 8.

Go to the next step.

INSPECT THROTTLE ACTUATOR

CONTROL CIRCUIT FOR SHORT
TO POWER SUPPLY

Turn the ignition switch to the ON
position (Engine off).

Measure voltage between the

following circuits:

{

Throttle actuator terminal A
(wiring harness-side) and

body ground.

{

Throttle actuator terminal B
(wiring harness-side) and

body ground.

Are there voltage B+?

Yes

Repair or replace suspected part, then go to

Step 8.

Go to the next step.

INSPECT THROTTLE ACTUATOR

CONTROL CIRCUITS FOR SHORT
EACH OTHER

Turn the ignition switch off.

Disconnect the throttle body and

PCM connector.

Measure resistance between
throttle actuator terminal A and B.

Is the resistance

more than 10

kilohms?

Yes

Go to the next step.

Repair or replace suspected part, then go to

Step 8.

INSPECT THROTTLE ACTUATOR

Yes

Replace the throttle body, then go to Step

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:38 AM

Page 400

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды