manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

z

Female terminal opening is loose.  

z

Coupler (pin holder) damage  

z

Pin discoloration (blackness)  

{

If the #3 terminal measures other than 

B+

 , inspect the following: 

z

Open or short circuit in wiring harness  

z

Harness/pin crimp is loose or disconnected.  

THERMISTOR TYPE (IAT SENSOR AND CHT SENSOR) 

Fig. 12: IAT Sensor And CHT Sensor Diagram

 

Courtesy of MAZDA MOTORS CORP.

 

INPUT SIGNAL SYSTEM INSPECTION FOR THERMISTOR TYPE 

1. When an irregular signal is detected, measure the #1 PCM terminal voltage. 

z

If the #1 terminal voltage and the M-MDS monitor voltage are the same, proceed to the next step.  

z

If there is a difference of 

0.5 V or more

 , inspect the following points concerning the PCM 

connector: 

„

Female terminal opening loose  

„

Coupler (pin holder) damage  

„

Pin discoloration (blackness)  

„

Harness/pin crimp is loose or disconnected.  

2. Measure the #2 sensor terminal voltage. 

z

If there is a 

0.5 V or more

 difference between the sensor and the M-MDS voltages, inspect the 

wiring harness for open or short circuits.  

z

If the sensor and the M-MDS voltages are the same, inspect the following points concerning the 

sensor connector: 

„

Female terminal opening is loose.  

„

Coupler (pin holder) damage  

„

Pin discoloration (blackness)  

„

Harness/pin crimp is loose or disconnected.  

z

If there are no problems, proceed to next investigation below. 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:38 AM

Page 101 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

J-Top COMPACT Instructions preview
COMPACT
Бренд: J-Top Страницы: 2
OEM Audio Reference Series Manual preview
Reference Series
Бренд: OEM Audio Страницы: 29
Axxess AXGMLN-08 Installation Instructions Manual preview
AXGMLN-08
Бренд: Axxess Страницы: 8
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Бренд: Kolpin Outdoors Страницы: 6
Schartec CR 4 Manual preview
CR 4
Бренд: Schartec Страницы: 2
Ford Windstar 2003 Quick Reference Manual preview
Windstar 2003
Бренд: Ford Страницы: 2
Mazda 2007 MazdaSpeed6 Specification preview
2007 MazdaSpeed6
Бренд: Mazda Страницы: 12
Renault ALASKAN 2017 Driver'S Handbook Manual preview
ALASKAN 2017
Бренд: Renault Страницы: 340
Mercedes-Benz 2016 SLK Operator'S Manual preview
2016 SLK
Бренд: Mercedes-Benz Страницы: 358
GAC MOTOR EMPOW Manual preview
EMPOW
Бренд: GAC MOTOR Страницы: 356
SNIPER V2 Inox Owner'S Manual preview
V2 Inox
Бренд: SNIPER Страницы: 2
iDataLink ADS-TBSL-GM Install Manual preview
ADS-TBSL-GM
Бренд: iDataLink Страницы: 6
Kogan CERTA CTCVINCVR14A User Manual preview
CERTA CTCVINCVR14A
Бренд: Kogan Страницы: 4
Blaupunkt 7 608 502 000 Installation Instructions Manual preview
7 608 502 000
Бренд: Blaupunkt Страницы: 6
Mitsubishi Outlander Plug-in hybrid Quick Manual preview
Outlander Plug-in hybrid
Бренд: Mitsubishi Страницы: 28
Discount Car Stereo A2DIY-JAG98 Quick Start Manual preview
A2DIY-JAG98
Бренд: Discount Car Stereo Страницы: 11
Phonocar 6/946 Instruction Manual preview
6/946
Бренд: Phonocar Страницы: 4
Hamron 012463 Operating Instructions Manual preview
012463
Бренд: Hamron Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды