Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 852

Страница: 852 / 1056

{

PCM terminal 2AH-TP

sensor terminal E

{

PCM terminal 2Z-TP sensor

terminal F

Does the engine start with the throttle
valve closed?

Yes

Go to Step 29.

Go to the next step.

Will the engine start and run smoothly

at part throttle?

Yes

Inspect the electronic throttle control

system operation.
(See

ENGINE CONTROL SYSTEM

OPERATION INSPECTION [MZI-
3.5]

Go to the next step.

Connect the M-MDS to the DLC-2.

Access RPM PID.
Is RPM PID indicating the engine

speed when cranking the engine?

Yes

Go to the next step.

Inspect for the following:

Open or short circuit in CKP
sensor

Open or short circuit in wiring

harness between CKP sensor
terminal A and PCM terminal 2P

Open or short circuit in wiring

harness between CKP sensor
terminal B and PCM terminal 2T

Open or short circuit in CKP
sensor wiring harnesses

If CKP sensor and wiring harness are
normal, go to the next step.

Visually inspect the CKP sensor and

teeth of crankshaft pulley.
Are CKP sensor and teeth of

crankshaft pulley normal?

Yes

Go to the next step.

Replace the malfunctioning part.

Inspect the ignition coil related wiring

harness condition (intermittent open or
short circuit) for all cylinders. Are

wiring harness conditions normal?

Yes

Go to the next step.

Repair the wiring harnesses.

Perform the spark test.
(See

ENGINE CONTROL SYSTEM

OPERATION INSPECTION [MZI-
3.5]

Is strong blue spark visible at each
cylinder?

Yes

Go to the next step.

Repair or replace the malfunctioning

part according to spark test result.

Inspect the spark plug conditions.

Yes

Spark plug is wet or covered with

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:37 AM

Page 35

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды