Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 207

Страница: 207 / 1056

9. Remove the compression gauge.

10. Install the spark plugs. (see

SPARK PLUG REMOVAL/INSTALLATION [MZI-3.5]

11. Install the ignition coils. (see

IGNITION COIL REMOVAL/INSTALLATION [MZI-3.5]

12. Install the dynamic chamber and throttle body as a single unit. (see

INTAKE-AIR SYSTEM

REMOVAL/INSTALLATION [MZI-3.5]

13. Install the engine cover. (See

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.5]

14. Install the fuel pump relay.
15. Complete the "AFTER REPAIR PROCEDURE". (see

AFTER REPAIR PROCEDURE [MZI-3.5]

TIMING CHAIN REMOVAL/INSTALLATION [MZI-3.5]

1. Drain the engine oil. (see

ENGINE OIL REPLACEMENT [MZI-3.5]

2. Remove the engine and transaxle component. (See

ENGINE REMOVAL/INSTALLATION [MZI-

3.5]

3. Secure the engine and transaxle component using a hoist and the

SST.

4. Remove the dynamic chamber and throttle body as a single unit. (see

INTAKE-AIR SYSTEM

REMOVAL/INSTALLATION [MZI-3.5]

5. Remove the ignition coils. (see

IGNITION COIL REMOVAL/INSTALLATION [MZI-3.5]

6. Remove the dipstick.

158}

118}

188}

141}

218}

163}

248}

186}

1,103

{11.24,

160}

827 {8.43,

120}

1,310

{13.35,

190}

979 {9.98,

142}

1,517

{15.46,

220}

1,138

{11.60,

165}

1,724

{17.57,

250}

1,289

{13.14,

187}

1,110

{11.31,

161}

834 {8.50,

121}

1,324

{13.49,

192}

993 {10.2,

144}

1,631

{16.62,

222}

1,145

{11.67,

166}

WARNING:

Fuel vapor is hazardous. It can very easily ignite, causing serious

injury and damage. Always keep sparks and flames away from fuel.

Fuel line spills and leakage are dangerous. Fuel can ignite and cause
serious injures or death and damage. Fuel can also irritate skin and

eyes. To prevent this, always complete the "Fuel Line Safety

Procedure". (see BEFORE REPAIR PROCEDURE [MZI-3.5] .)

Continuous exposure to USED engine oil has caused skin cancer in
laboratory mice. Protect your skin by washing with soap and water

immediately after working with engine oil.

NOTE:

The following procedure "TIMING CHAIN REMOVAL/INSTALLATION" is

performed after the engine and transaxle component is removed from the
vehicle. (See ENGINE REMOVAL/INSTALLATION [MZI-3.5].)

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:27 AM

Page 16

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды