manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

Access RPM PID. 
Is RPM PID indicating engine speed 

during engine cranking?

No

Inspect for the following: 

z

Open or short circuit in CKP 

sensor  

z

Open or short circuit in wiring 
harness between CKP sensor 

terminal A and PCM terminal 2P  

z

Open or short circuit in wiring 
harness between CKP sensor 

terminal B and PCM terminal 2T  

z

Open or short circuit in CKP 
sensor wiring harnesses  

 
If CKP sensor and wiring harness are 

normal, go to the next step.

15

Visually inspect CKP sensor and teeth 
of crankshaft pulley. 

Are CKP sensor and teeth of crankshaft 
pulley normal?

Yes

Go to the next step.

No

Replace the malfunctioning part.

16

Inspect the ignition coil related wiring 
harness condition (intermittent open or 

short circuit) for all cylinders. Are 
wiring harness conditions normal?

Yes

Go to the next step.

No

Repair the wiring harnesses.

17

Perform the spark test. 

(See 

ENGINE CONTROL SYSTEM 

OPERATION INSPECTION [MZI-

3.5]

.) 

Is strong blue spark visible at each 

cylinder?

Yes

Go to the next step. 

If symptoms occurs with the A/C on, go 
to Step 24.

No

Repair or replace the malfunctioning part 

according to spark test result.

18

Inspect the spark plug condition. 

Is spark plug wet, covered with carbon 
or grayish white?

Yes

Spark plug is wet or covered with 

carbon:

  

Inspect for fuel leakage from injector. 

Spark plug is grayish white:

  

Inspect the fuel injector for clogging.

No

Install spark plugs on original cylinders.

Go to the next step.

19

Remove and shake the PCV valve. 
Does the PCV valve rattle?

Yes

Go to the next step.

No

Replace the PCV valve.

20

visually inspect the exhaust system 

part. 
Is there any deformed exhaust system 

part?

Yes

Replace the suspected part.

No

Go to the next step.

21

Install the fuel pressure gauge between 
the fuel pipe and the fuel distributor. 

Yes

Go to the next step.

No

Zero or low:

  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:37 AM

Page 27 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

GMC HUMMER EV 2022 Manual preview
HUMMER EV 2022
Бренд: GMC Страницы: 140
Whispbar K728W Fitting Instructions Manual preview
K728W
Бренд: Whispbar Страницы: 85
Ranger design 1506-PHX Cargo Plus Installation Manual preview
1506-PHX Cargo Plus
Бренд: Ranger design Страницы: 8
AUTOTECH 10.411.01.219K Installation Instructions preview
10.411.01.219K
Бренд: AUTOTECH Страницы: 1
Quadratec 11113.1435 Quick Start Manual preview
11113.1435
Бренд: Quadratec Страницы: 14
Mazda 2010 MX-5 Miata Specification preview
2010 MX-5 Miata
Бренд: Mazda Страницы: 8
Toyota RAV-4 2015 Series Owner'S Manual Supplement preview
RAV-4 2015 Series
Бренд: Toyota Страницы: 50
Tesla MODEL Y Owner'S Manual preview
MODEL Y
Бренд: Tesla Страницы: 274
Whispbar WB201 Manual preview
WB201
Бренд: Whispbar Страницы: 14
Goobay KFZ 112 Quick Start Manual preview
KFZ 112
Бренд: Goobay Страницы: 2
Lexus rx450h 2015 Owner'S Manual preview
rx450h 2015
Бренд: Lexus Страницы: 878
HUSKY LINERS 47954 Installation Instructions preview
47954
Бренд: HUSKY LINERS Страницы: 4
iOttie HLCRIO138 Manual preview
HLCRIO138
Бренд: iOttie Страницы: 19
Prorack K129 Fitting Instructions Manual preview
K129
Бренд: Prorack Страницы: 13
Ericsson M-RK 344A4616P1 Installation & Operator'S Manual preview
M-RK 344A4616P1
Бренд: Ericsson Страницы: 28
Falcon FN-WCCS-W User Manual preview
FN-WCCS-W
Бренд: Falcon Страницы: 36
Audiovox CMT9300 Installation Manual preview
CMT9300
Бренд: Audiovox Страницы: 7
Cramaro FARP WORKS CRUSHED CAR Manual preview
FARP WORKS CRUSHED CAR
Бренд: Cramaro Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды