manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

3. Perform the KOER self-test. (see 

KOEO/KOER SELF TEST [MZI-3.5]

 .).  

4. Verify that the DTC P0483 is not shown and the cooling fan operates during the KOER self-test. 

z

If DTC P0480 is shown, perform the DTC troubleshooting procedure. 

(see 

DTC TABLE [MZI-3.5]

 .) 

z

If the cooling fans do not operate, proceed to the following: 

1. Verify the clicking sound of the cooling fan relay when the ignition switch is turned from the 

off to the ON position.  

2. If there is no the clicking sound, inspect the cooling fan relay for an open circuit between the 

ignition switch and the cooling fan relay.  

z

If there is a clicking sound, go to the next step.  

z

Inspect the following parts in the indicated order in accordance with fan operation conditions.  

Cooling fans do not operate 

z

Open circuit between the fan control module and the cooling fan relay  

z

Open circuit between fan control module and ground  

z

Poor connection of the fan control module connector  

z

Fan control module (see 

FAN CONTROL MODULE INSPECTION [MZI-3.5]

 .)  

Cooling fan motor No.1 does not operate 

z

Open or short to ground circuit between the fan control module and cooling fan motor No.1  

z

Poor connection of the fan control module connector or cooling fan motor No.1 connector  

z

Cooling fan motor No.1 (see 

FAN MOTOR INSPECTION [MZI-3.5]

 .)  

z

Fan control module (see 

FAN CONTROL MODULE INSPECTION [MZI-3.5]

 .)  

Cooling fan motor No.2 does not operate 

z

Open or short to ground circuit between the fan control module and the cooling fan motor No.2  

z

Poor connection of the fan control module connector or the cooling fan motor No.1 connector  

z

Cooling fan motor No.2 (see 

FAN MOTOR INSPECTION [MZI-3.5]

 .)  

z

Fan control module (see 

FAN CONTROL MODULE INSPECTION [MZI-3.5]

 .)  

VARIABLE VALVE TIMING CONTROL SYSTEM OPERATION INSPECTION 

When idling cannot be continued 

1. Remove the OCV and verify that the spool valve is at maximum retard position. 

NOTE:

z

Inspect for each bank 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:38 AM

Page 110 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Calix M5T 187A Assembly Instructions preview
M5T 187A
Бренд: Calix Страницы: 5
PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Бренд: PUTCO Страницы: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Бренд: Westfalia Страницы: 18
Wagan 2227-1 User Manual preview
2227-1
Бренд: Wagan Страницы: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Бренд: Thermo King Страницы: 2
GReddy Intercooler Kit Type 31 Installation Manual preview
Intercooler Kit Type 31
Бренд: GReddy Страницы: 9
minnid 1.240.344 Operating Instructions Manual preview
1.240.344
Бренд: minnid Страницы: 44
Icom RMK-5 Instruction Manual preview
RMK-5
Бренд: Icom Страницы: 20
Pet Gear TRI-FOLD PG9300RF Instruction Manual preview
TRI-FOLD PG9300RF
Бренд: Pet Gear Страницы: 4
Warn 70948 Installation Instructions preview
70948
Бренд: Warn Страницы: 5
TATA Motors Harrier 2021 Owner'S Manual preview
Harrier 2021
Бренд: TATA Motors Страницы: 308
Mopar 2005-2009 Chrysler 300C Installation Instructions Manual preview
2005-2009 Chrysler 300C
Бренд: Mopar Страницы: 7
Federal Signal Corporation HighLighter Installation And Programming preview
HighLighter
Бренд: Federal Signal Corporation Страницы: 20
Metra Electronics 99-3305 Installation Instructions Manual preview
99-3305
Бренд: Metra Electronics Страницы: 12
EUFAB 16559 Operating Instructions Manual preview
16559
Бренд: EUFAB Страницы: 12
RAM TRUCK 2500 2017 Owner'S Manual Supplement preview
TRUCK 2500 2017
Бренд: RAM Страницы: 33
Kargo Master PRO-II KS Assembly Instructions Manual preview
PRO-II KS
Бренд: Kargo Master Страницы: 8
National Cycle Quantum Wash'n'Wipe N30205 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30205
Бренд: National Cycle Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды