Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 510

Страница: 510 / 1056

INSPECTION [MZI-3.5]

Then go to Step 18.

Go to Step 18.

INSPECT FUEL LINE FROM FUEL

PUMP TO FUEL DELIVERY PIPE

Visually inspect the fuel line for
any leakage.

Is any fuel leakage found?

Yes

Replace suspected fuel line, then go to Step

18.

Inspect the low-pressure side fuel filter for
the following:

Foreign material or staining inside the

fuel filter Perform the following
actions as a result:

If foreign material or staining is found
inside the fuel filter (low-pressure

side), clean the fuel tank and filter.

If normal, replace the fuel pump unit.

(see

FUEL PUMP UNIT

REMOVAL/INSTALLATION

[MZI-3.5]

Then, go to Step 18.

INSPECT ENGINE
COMPRESSION

Inspect the engine compression.

(see

COMPRESSION

INSPECTION [MZI-3.5]

Is it normal?

Yes

Go to the next step.

Perform an engine overhaul for repairs, then

go to Step 18.

INSPECT VARIABLE VALVE
TIMING CONTROL SYSTEM

OPERATION

Inspect the variable valve timing
control system operation.

(see

ENGINE CONTROL

SYSTEM OPERATION

INSPECTION [MZI-3.5]

Does the variable timing control

Yes

Go to the next step.

Repair or replace the malfunctioning part

according to the variable valve timing
control system inspection results, then go to

Step 18.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:31 AM

Page 163

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды