manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

z

Is any related Service Bulletins 

available?  

No

Go to the next step.

3

INSPECT FUEL INJECTOR NO.5 

CONNECTOR FOR POOR 
CONNECTION

 

z

Turn the ignition switch off.  

z

Disconnect the fuel injector No.5 

connector.  

z

Inspect for poor connection (such as 

damaged/pulled-out pins, 
corrosion).  

z

Are there malfunction?  

Yes

Repair or replace suspected part, then go 

to Step 8.

No

Go to the next step.

4

INSPECT PCM CONNECTOR FOR 

POOR CONNECTION

 

z

Turn the ignition switch off.  

z

Disconnect the PCM connector.  

z

Inspect for poor connection (such as 

damaged/pulled-out pins, 
corrosion).  

z

Is there malfunction?  

Yes

Repair or replace suspected part, then go 

to Step 8.

No

Go to the next step.

5

INSPECT FUEL INJECTOR NO.5 

POWER SUPPLY CIRCUIT FOR 
OPEN CIRCUIT

 

z

Turn the ignition switch to the ON 
position (Engine off).  

z

Measure the voltage between fuel 

injector No.5 connector terminal B 
and body ground.  

z

Is the voltage 

B+

 ?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go 
to Step 8.

6

INSPECT FUEL INJECTOR NO.5 

SIGNAL CIRCUIT FOR OPEN 
CIRCUIT

 

z

Inspect continuity between fuel 
injector No.5 terminal A (wiring 

harness-side) and PCM terminal 
2BB (wiring harness-side).  

z

Is there continuity?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go 

to Step 8.

7

INSPECT FUEL INJECTOR NO.5

 

Yes

Replace the fuel injector No.5, then go 

to the next step.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:31 AM

Page 135 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

A-Tach Mounts 50131 Instructions preview
50131
Бренд: A-Tach Mounts Страницы: 2
JETBAG 320 Fitting Instructions Manual preview
320
Бренд: JETBAG Страницы: 44
Mitsubishi 1998 FTO Technical Information Manual preview
1998 FTO
Бренд: Mitsubishi Страницы: 160
Cadillac 2004 CTS Owner'S Manual preview
2004 CTS
Бренд: Cadillac Страницы: 442
Monacor CARPOWER CAP-12XHQ Manual preview
CARPOWER CAP-12XHQ
Бренд: Monacor Страницы: 5
Jeep Grand Cherokee WK2 Owner'S Manual preview
Grand Cherokee WK2
Бренд: Jeep Страницы: 338
Camcar 40108 Mounting Instructions preview
40108
Бренд: Camcar Страницы: 6
ABL eMH3 Quick Start Manual preview
eMH3
Бренд: ABL Страницы: 4
Compass 02106 Manual preview
02106
Бренд: Compass Страницы: 16
Chevrolet 1999 Malibu Owner'S Manual preview
1999 Malibu
Бренд: Chevrolet Страницы: 344
Prorack K692 Fitting Instructions Manual preview
K692
Бренд: Prorack Страницы: 15
STO N SHO SNS135a Installation Procedures Manual preview
SNS135a
Бренд: STO N SHO Страницы: 7
Weltmann KFZ-Teile 9B500016 Fitting Instructions Manual preview
9B500016
Бренд: Weltmann KFZ-Teile Страницы: 12
RBO IT FITS RBO1018 Product Manual preview
IT FITS RBO1018
Бренд: RBO Страницы: 36
Chrysler Dodge Caravan 2002 Manual preview
Dodge Caravan 2002
Бренд: Chrysler Страницы: 2399
Ednet 84104 User Manual preview
84104
Бренд: Ednet Страницы: 6
Volvo Ski box Installation Instructions Manual preview
Ski box
Бренд: Volvo Страницы: 7
Hama 00046080 Instructions For Use preview
00046080
Бренд: Hama Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды