Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 210

Страница: 210 / 1056

2. Set a flathead screwdriver to the drive plate in the position indicated in the figure to lock the crankshaft

rotation.

3. Remove the crankshaft pulley lock bolt and washer.

Fig. 18: Using Screwdriver To Lock Drive Plate

Courtesy of MAZDA MOTORS CORP.

CRANKSHAFT PULLEY REMOVAL NOTE

1. Remove the washer from the crankshaft pulley lock bolt, install a suitable spacer (thickness:

approx. 14

mm {0.55 in},

diameter:

approx. 30 mm {1.18 in}),

(similar to front shock absorber lower nut) to the

crankshaft pulley lock bolt, and install the crankshaft pulley lock bolt to the crankshaft.

Fig. 19: Identifying Crankshaft Pulley Lock Bolt

Courtesy of MAZDA MOTORS CORP.

2. Remove the crankshaft pulley using the

SST.

3. Remove the crankshaft pulley lock bolt and spacer.

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:27 AM

Page 19

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды