manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

3.5]

 .)

11

Visually inspect for fuel leakage at fuel 

injector O-ring and fuel line. 
Service if necessary. 

Is fuel line pressure held after ignition 
switch is turned off? 

(see 

FUEL LINE PRESSURE 

INSPECTION [MZI-3.5]

 .)

Yes

Go to the next step.

No

Inspect the fuel injector. 

If the fuel injector is normal, replace the 
fuel pump unit. 

(see 

FUEL PUMP UNIT 

REMOVAL/INSTALLATION [MZI-

3.5]

 .)

12

Connect a pressure gauge to A/C low 

and high pressure side lines.Turn the 
A/C on and measure low side and high 

side pressure.Are pressures within 
specifications?(see 

REFRIGERANT 

PRESSURE CHECK

 .)

NOTE:

z

The following test is for engine 
stall with the A/C on. If other 

symptom exists, go to the next 
step.  

Yes

Go to the next step.

No

If the A/C is always on, go to symptom 

troubleshooting "No.24 A/C is always on 
or A/C compressor runs continuously". 

(See 

NO.24 A/C IS ALWAYS ON OR 

A/C COMPRESSOR RUNS 

CONTINUOUSLY [MZI-3.5]

.) 

For other symptoms, inspect the 

following: 

z

Refrigerant charging amount  

z

Condenser fan operation  

13

Inspect cruise control system.Is cruise 
control system normal?

NOTE:

z

The following test should be 
performed for symptom with 

cruise control ON. If other 
symptoms exist, go to the next 

step.  

Yes

Go to the next step.

No

Repair or replace the malfunctioning 

part.

14

Inspect the front HO2S. 
(see 

FRONT HEATED OXYGEN 

SENSOR (HO2S) INSPECTION 
[MZI-3.5].

 ) 

Is the front HO2S normal?

Yes

Go to the next step.

No

Replace the front HO2S. 
(see 

REAR HEATED OXYGEN 

SENSOR (HO2S) 
REMOVAL/INSTALLATION [MZI-

3.5].

 )

15

Inspect the evaporative purge hose 
between the fuel tank and the purge 

valve. 
Does fuel flow into evaporative purge 

hose?

Yes

Inspect the check valve (two-way). 
(see 

FUEL TANK INSPECTION 

[MZI-3.5]

 .)

No

Go to the next step.

16

Disconnect the vacuum hose between 

the purge solenoid valve and the intake 
manifold from the purge solenoid 

valve side. 
Plug opening end of vacuum hose. 

Yes

Go to the next step. 

Inspect if the purge solenoid valve is 
stuck open mechanically. 

Inspect the evaporative emission control 
system.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:37 AM

Page 52 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

AC Schnitzer F40 Fitting Instructions Manual preview
F40
Бренд: AC Schnitzer Страницы: 16
TATA Motors Nano Owner'S Manual & Service Book preview
Nano
Бренд: TATA Motors Страницы: 94
GÄN GA Manual preview
GA
Бренд: GÄN Страницы: 24
Daihatsu TERIOS J100 Maintenance Manual preview
TERIOS J100
Бренд: Daihatsu Страницы: 43
OEM Audio Reference Series Manual preview
Reference Series
Бренд: OEM Audio Страницы: 29
Jacobsen Cushman Turf Truckster Parts & Maintenance Manual preview
Cushman Turf Truckster
Бренд: Jacobsen Страницы: 210
Prorack K383 Fitting Instructions Manual preview
K383
Бренд: Prorack Страницы: 14
Thule 1308 Instructions Manual preview
1308
Бренд: Thule Страницы: 8
KRAFTWERK Automotive 31006 Instructions preview
Automotive 31006
Бренд: KRAFTWERK Страницы: 2
FALCON RIDGE HO-P500-FC04 Instructions For Installation And Care preview
HO-P500-FC04
Бренд: FALCON RIDGE Страницы: 8
Scosche 142HUD2 Manual preview
142HUD2
Бренд: Scosche Страницы: 8
Dodge Challenger 2013 Owner'S Manual preview
Challenger 2013
Бренд: Dodge Страницы: 543
Kargo Master 8006A Instruction Manual preview
8006A
Бренд: Kargo Master Страницы: 19
Safe Fleet PRIME DESIGN VBR3-FT31B Manual preview
PRIME DESIGN VBR3-FT31B
Бренд: Safe Fleet Страницы: 12
Metra Electronics 99-7860 Installation Instructions preview
99-7860
Бренд: Metra Electronics Страницы: 5
Renkforce RF-4743771 Operating Instructions preview
RF-4743771
Бренд: Renkforce Страницы: 4
Alfa Romeo 1966 Spider 105 Faq preview
1966 Spider 105
Бренд: Alfa Romeo Страницы: 46
Subaru 2003 Baja Owner'S Manual preview
2003 Baja
Бренд: Subaru Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды