Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 10

Страница: 10 / 1056

Open circuit

If there is no continuity, the circuit is open. Repair or replace the wiring harness.

{

Throttle body terminal A and PCM terminal 2BO

{

Throttle body terminal B and PCM terminal 2BR

Short circuit

If there is continuity, the circuit is shorted. Repair or replace the wiring harness.

{

Throttle body terminal A and power supply

{

Throttle body terminal A and ground

{

Throttle body terminal B and power supply

{

Throttle body terminal B and ground

ACCELERATOR PEDAL REMOVAL/INSTALLATION [MZI-3.5]

1. Disconnect the negative battery cable. (see

BATTERY REMOVAL/INSTALLATION [MZI-3.5]

2. Remove the dashboard under cover (Driver side). (see

DASHBOARD UNDER COVER

REMOVAL/INSTALLATION

3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.

Fig. 12: Identifying Accelerator Pedal And Electrical Connector With Torque Specifications

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Intake-Air System (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:23:32 AM

Page 10

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды