manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

Fig. 27: View Of LH HO2S With Torque Specifications

Courtesy of MAZDA MOTORS CORP.

 

HO2S (RH) REMOVAL/INSTALLATION 

1. Disconnect the negative battery cable.  
2. Remove the following part for easier access. 

1. Remove the cowl panel. (see 

COWL PANEL REMOVAL/INSTALLATION

 .)  

3. Disconnect the HO2S (RH) connector. 

4. Remove the HO2S (RH) using the 

SST.

 

5. Install in the reverse order of removal. 

Fig. 28: View Of RH HO2S With Torque Specifications

 

Courtesy of MAZDA MOTORS CORP.

 

REAR HEATED OXYGEN SENSOR (HO2S) INSPECTION [MZI-3.5] 

REAR HEATED OXYGEN SENSOR (HO2S) VOLTAGE INSPECTION 

1. Warm up the engine to normal operating temperature.  
2. Using the M-MDS, monitor the following: 

{

Vehicle speed (PID: VSS)  

NOTE:

z

If necessary, lubricate the HO2S (RH) with Penetrating and Lock 

Lubricant loosen to aid in removal.  

NOTE:

z

Apply a light coat of anti-seize lubricant to the threads of the HO2S. 

NOTE:

z

Before performing the following inspection, make sure to follow the 

procedure as indicated in the troubleshooting flowchart. (see HOW TO 

USE THIS MANUAL .)  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Control System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:25:31 AM

Page 31 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

JAC S5 Workshop Manual preview
S5
Бренд: JAC Страницы: 70
Jeep Cherokee 16 1982 Technical & Service Manual preview
Cherokee 16 1982
Бренд: Jeep Страницы: 1311
Toyota RX450h 2010 Emergency Response Manual preview
RX450h 2010
Бренд: Toyota Страницы: 35
iDataLink BLADE-AL(TB)-TL2 Install Manual preview
BLADE-AL(TB)-TL2
Бренд: iDataLink Страницы: 9
Magneti Marelli BCF184 Installation Instructions preview
BCF184
Бренд: Magneti Marelli Страницы: 2
RBP STEALTH POWER RBP-216-SP Installation Manual preview
STEALTH POWER RBP-216-SP
Бренд: RBP Страницы: 16
HURST STREET SUPER SHIFTER Installation Instructions preview
STREET SUPER SHIFTER
Бренд: HURST Страницы: 2
Safe Fleet inView 360 Fusion Calibration Manual preview
inView 360 Fusion
Бренд: Safe Fleet Страницы: 27
Seat ROADSIDE ASSISTANCE Handbook preview
ROADSIDE ASSISTANCE
Бренд: Seat Страницы: 44
Chevrolet Malibu 2014 Owner'S Manual preview
Malibu 2014
Бренд: Chevrolet Страницы: 428
MULTILIFT ULTIMA S Installation Instructions Manual preview
ULTIMA S
Бренд: MULTILIFT Страницы: 62
JBL smartbase Quick Start Manual preview
smartbase
Бренд: JBL Страницы: 12
Honda 2006 Accord Owner'S Manual preview
2006 Accord
Бренд: Honda Страницы: 569
BENDIX A-18 TRAILER ABS Manual preview
A-18 TRAILER ABS
Бренд: BENDIX Страницы: 40
Toyota RAV4 HV 2016 Quick Reference Manual preview
RAV4 HV 2016
Бренд: Toyota Страницы: 56
Enduro EM203 User Manual preview
EM203
Бренд: Enduro Страницы: 52
Mercedes-Benz A 150 Owner'S Manual preview
A 150
Бренд: Mercedes-Benz Страницы: 305
Volvo S90 TWIN ENGINE Owner'S Manual preview
S90 TWIN ENGINE
Бренд: Volvo Страницы: 662

Бренды по названию

Популярные бренды

Загрузить еще бренды