manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

Fig. 2: Identifying "Fl22" Mark On Cooling System Cap

 

Courtesy of MAZDA MOTORS CORP.

 

1. Verify that the engine coolant level in the coolant reserve tank is between the F and L marks. 

z

If the engine coolant level is below the L mark, add engine coolant.  

Fig. 3: Identifying Engine Coolant Level In Coolant Reserve Tank

 

Courtesy of MAZDA MOTORS CORP.

 

ENGINE COOLANT PROTECTION INSPECTION [MZI-3.5] 

1. Measure the engine coolant temperature and specific gravity using a thermometer and a hydrometer. 

CAUTION:

z

Use engine coolant at a concentration that meets the 
environmental conditions in which the vehicle is driven, 

otherwise engine damage could occur.  

z

The engine has aluminum parts and must be protected by an 

ethylene-glycol-based coolant to prevent corrosion and 
freezing.  

z

Do not use coolants containing Alcohol, Methanol, Borate or 
Silicate. These coolants could damage the cooling system.  

z

Use only soft (demineralized) water in the coolant mixture. 

Water that contains minerals will cut down on the coolant's 

effectiveness.  

z

Engine coolant damages paint. If engine coolant does get on a 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE Cooling System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:31:38 AM

Page 4 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

LaserTrack Flare Installation Manual preview
Flare
Бренд: LaserTrack Страницы: 12
GARO ENTITY PRO Installation preview
ENTITY PRO
Бренд: GARO Страницы: 2
HUSKY LINERS X-ACT CONTOUR 53491 Care And Use Instructions preview
X-ACT CONTOUR 53491
Бренд: HUSKY LINERS Страницы: 2
Volvo 30728293 Installation Instructions Manual preview
30728293
Бренд: Volvo Страницы: 19
Pacbrake C44059 Installation Manual preview
C44059
Бренд: Pacbrake Страницы: 14
Chevrolet 2013 Spark Specifications preview
2013 Spark
Бренд: Chevrolet Страницы: 2
Volvo 2004 V70 (Swedish) Användarmanual preview
2004 V70
Бренд: Volvo Страницы: 188
Pacbrake HP10098 Installation Manual preview
HP10098
Бренд: Pacbrake Страницы: 6
Flash Cover MN019 Instructions preview
MN019
Бренд: Flash Cover Страницы: 2
Porsche WTY 2010 Warranty & Maintenance Manual preview
WTY 2010
Бренд: Porsche Страницы: 98
rough country 921107830 Installation Instruction preview
921107830
Бренд: rough country Страницы: 4
r.LiNK RL2-MMI3G-GW Manual preview
RL2-MMI3G-GW
Бренд: r.LiNK Страницы: 21
Oldsmobile 1994 Bravada Owner'S Manual preview
1994 Bravada
Бренд: Oldsmobile Страницы: 248
Meritor 93000 Service Service Manual preview
93000 Service
Бренд: Meritor Страницы: 20
Stealthbox SB-J-GCHER2/10W3v2 Installation Manual preview
SB-J-GCHER2/10W3v2
Бренд: Stealthbox Страницы: 2
Buick 1997 Skylark Owner'S Manual preview
1997 Skylark
Бренд: Buick Страницы: 371
Brodit ProClip 854399 Installation Instructions preview
ProClip 854399
Бренд: Brodit Страницы: 2
Seat Toledo 2019 Owner'S Manual preview
Toledo 2019
Бренд: Seat Страницы: 300

Бренды по названию

Популярные бренды

Загрузить еще бренды