Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 39

Страница: 39 / 1056

Fig. 13: Inserting Flathead Screwdriver Into Upper Mount Rubber Bracket Notch

Courtesy of MAZDA MOTORS CORP.

2. Apply force in the direction shown by the arrow.

Fig. 14: Applying Downward Force

Courtesy of MAZDA MOTORS CORP.

RADIATOR REMOVAL NOTE

1. Remove the radiator from above the engine compartment.

THERMOSTAT REMOVAL/INSTALLATION [MZI-3.5]

WARNING:

Never remove the cooling system cap or loosen the radiator drain

plug while the engine is running, or when the engine and radiator are

hot. Scalding engine coolant and steam may shoot out and cause
serious injury. It may also damage the engine and cooling system.

Turn off the engine and wait until it is cool. Even then, be very

careful when removing the cap. Wrap a thick cloth around it and

slowly turn it counterclockwise to the first stop. Step back while the
pressure escapes.

When you are sure all the pressure is gone, press down on the cap

using the cloth, turn it, and remove it.

2007 Mazda CX-9 Grand Touring

2007 ENGINE Cooling System (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:31:38 AM

Page 14

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды