Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 196

Страница: 196 / 1056

7. Install the generator and A/C drive belt.

Fig. 4: Setting Breaker Bar On Center Of Tensioner Pulley

Courtesy of MAZDA MOTORS CORP.

8. Verify that the drive belt auto tensioner indicator mark is within the maximum and minimum belt length.

(See

DRIVE BELT INSPECTION [MZI-3.5]

If the drive belt auto tensioner indicator mark is not within the limit, replace the generator and A/C

drive belt.

9. Install the splash shield (RH).

10. Install the front wheel and tire (RH). (see

GENERAL PROCEDURES (SUSPENSION).

)

11. Install the engine cover. (See

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.5]

NOTE:

When the generator and A/C drive belt is replaced with a new one, the

drive belt auto tensioner indicator mark is aligned with the nominal

belt length mark.

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:27 AM

Page 5

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды