Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 838

Страница: 838 / 1056

NO.5 ENGINE STALLS-AFTER START/AT IDLE [MZI-3.5]

DESCRIPTION AND POSSIBLE CAUSES

Is there any contamination?

Visually inspect the exhaust system

part.
Is there any deformed exhaust system

part?

Yes

Replace the suspected part.

Go to the next step.

Inspect the starting system.
(see

STARTER INSPECTION

[MZI-3.5]

Is starting system normal?

Yes

Inspect for loose connectors or poor
terminal contact.

Repair or replace components as

required.

Verify test results.

{

If normal, return to diagnostic index to service any additional symptoms.

(See

ENGINE SYMPTOM TROUBLESHOOTING [MZI-3.5]

{

If malfunction remains, inspect related Service Bulletins and/or On-line Repair

Information and perform repair or diagnosis.

If vehicle is repaired, troubleshooting completed.

If vehicle is not repaired or additional diagnostic information is not
available, Replace the PCM.

(see

PCM REMOVAL/INSTALLATION [MZI-3.5]

ENGINE STALLS-AFTER START/AT IDLE

DESCRIPTION

Engine stops unexpectedly.

A/C system operation is improper

Air leakage from intake-air system parts

Purge solenoid valve malfunction

Improper operation of electronic throttle control system

No signal from CKP sensor due to sensor, related wire or wrong installation

Vacuum leakage

Engine overheating

Low engine compression

Erratic signal to ignition coil

Poor fuel quality

PCV valve malfunction

Air cleaner restriction

Restriction in exhaust system

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:36 AM

Page 21

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды