Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 419

Страница: 419 / 1056

DTC P0116 [MZI-3.5]

DTC P0116 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

DIAGNOSTIC PROCEDURE

DTC P0116 (MZI-3.5) DIAGNOSTIC PROCEDURE

Are any DTCs present?

DTC P0116

CHT sensor circuit range/performance

DETECTION
CONDITION

Indicates the engine coolant temperature logic test has failed. This DTC
indicates that the CHT value is higher than the calibrated value and could

prevent 1 or more OBD monitors from completing.

The PCM runs this logic after an engine off and a calibrated soak period
(typically 6 hours).

This soak period allows the IAT and the CHT to stabilize and not differ by
more than a calibrated value.

DTC P0116 is set when all of the following conditions are met:

{

The CHT at engine start exceeds the IAT at engine start by more than
a calibrated value, typically

17 °C {30 °F}.

{

The CHT exceeds a calibrated value, typically

107 °C {225 °F}.

{

The fuel system, heated oxygen and misfire monitors have not

completed.

{

The calibrated time to set DTC P0116 has expired.

POSSIBLE CAUSE

Cooling system malfunction

CHT sensor malfunction

STEP

INSPECTION

ACTION

VERIFY FREEZE FRAME DATA
HAS BEEN RECORDED

Has FREEZE FRAME DATA
been recorded?

Yes

Go to the next step.

Record FREEZE FRAME DATA on the
repair order, then go to the next step.

VERIFY RELATED REPAIR

INFORMATION AVAILABILITY

Verify related Service Bulletins

and/or on-line repair information
availability.

Is any related Service Bulletins

Yes

Perform repair or diagnosis according to

the available Service Bulletins.
If the vehicle is not repaired, go to next

step.

Go to the next step.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:29 AM

Page 72

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды