manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

DIAGNOSTIC PROCEDURE 

DTC P0506 (MZI-3.5) DIAGNOSTIC PROCEDURE

 

POSSIBLE CAUSE

 

z

Sludged throttle body  

z

Vacuum leakage  

z

Throttle body malfunction  

z

PCM malfunction  

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA 
HAS BEEN RECORDED

 

z

Has FREEZE FRAME DATA 
been recorded?  

Yes

Go to the next step.

No

Record FREEZE FRAME DATA on the to 
the next step. repair order, then go

2

VERIFY RELATED REPAIR 

INFORMATION AVAILABILITY

 

z

Verify related Service Bulletins 

and/or on-line repair information 
availability.  

z

Is any related Service Bulletins 

available?  

Yes

Perform repair or diagnosis according to 

the available Service Bulletins. 

z

If the vehicle is not repaired, then go 

to the next step.  

No

Go to the next step.

3

VERIFY RELATED PENDING OR 
STORED DTCS

 

z

Turn the ignition switch off then 
to the ON position (Engine off).  

z

Verify pending code or stored 

DTCs using the M-MDS.  

z

Is other DTC present?  

Yes

Repair applicable DTCs. 
(See 

DTC TABLE [MZI-3.5]

.)

No

Go to the next step.

4

INSPECT AIR CLEANER 
ELEMENT

 

z

Remove air cleaner element with 
the engine running.  

z

Is the engine speed increased?  

Yes

Replace the air cleaner element, then go to 
Step 7.

No

Go to the next step.

5

INSPECT INTAKE AIR SYSTEM 

FOR EXCESSIVE AIR SUCTION

 

z

Visually inspect the hose in intake 

air system for damages.  

z

Is there any malfunction?  

Yes

Repair or replace the malfunctioning part, 

then go to Step 7.

No

Go to the next step.

6

INSPECT THROTTLE BODY 

Yes

Clean or replace the throttle body passage, 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:33 AM

Page 259 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

LaserTrack Flare Installation Manual preview
Flare
Бренд: LaserTrack Страницы: 12
GARO ENTITY PRO Installation preview
ENTITY PRO
Бренд: GARO Страницы: 2
Ford E-Transit 2022 Manual preview
E-Transit 2022
Бренд: Ford Страницы: 22
Velleman CAMCOLC1N User Manual preview
CAMCOLC1N
Бренд: Velleman Страницы: 6
Xpresskit DBALL2-HYUNDAI9 Installation And Quick Reference Manual preview
DBALL2-HYUNDAI9
Бренд: Xpresskit Страницы: 13
RAM 2011 3500 Chassis Cab User Manual preview
2011 3500 Chassis Cab
Бренд: RAM Страницы: 92
minnid 1.240.344 Operating Instructions Manual preview
1.240.344
Бренд: minnid Страницы: 44
Draw tite 24943 Installation Instructions preview
24943
Бренд: Draw tite Страницы: 4
Mercedes-Benz CLS 280 2008 Owner'S Manual preview
CLS 280 2008
Бренд: Mercedes-Benz Страницы: 329
Waeco Perfect Fit MBM120 Installation Instructions preview
Perfect Fit MBM120
Бренд: Waeco Страницы: 3
Or-Fab HD Bumper Installation Instructions preview
HD Bumper
Бренд: Or-Fab Страницы: 4
Mobridge DA-G2 MOST150 Manual preview
DA-G2 MOST150
Бренд: Mobridge Страницы: 20
Kogan CERTA CTCVINCVR14A User Manual preview
CERTA CTCVINCVR14A
Бренд: Kogan Страницы: 4
Renault Laguna III Manual preview
Laguna III
Бренд: Renault Страницы: 3699
Diono easy view XXL Instructions Manual preview
easy view XXL
Бренд: Diono Страницы: 9
Mazda 2004 Mazda3 Quick Tips preview
2004 Mazda3
Бренд: Mazda Страницы: 12
Audiovox CMT9300 Installation Manual preview
CMT9300
Бренд: Audiovox Страницы: 7
Hotchkis 22101 Installation Manual preview
22101
Бренд: Hotchkis Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды