manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

Fig. 36: Identifying Fuel Hose And Checker Tab

 

Courtesy of MAZDA MOTORS CORP.

 

TYPE C INSTALLATION 

1. Inspect the fuel hose and fuel pipe sealing surface for damage and deformation. 

z

If there is any malfunction, replace it with a new one.  

2. Install the quick release connector. 

z

Insert the fuel pipe straight to the end of the quick release connector.  

z

Push down the retainer using a finger. 

„

If the retainer cannot be pushed down, push the fuel pipe further to the quick release 

connector.  

3. Lightly pull and push the quick release connector a few times by hand, and then verify that it is connected 

securely. 

Fig. 37: Installing Quick Release Connector

 

Courtesy of MAZDA MOTORS CORP.

 

TYPE D INSTALLATION 

NOTE:

z

If the quick release connector O-ring is damaged or has slipped, replace 
the fuel hose.  

NOTE:

z

If the quick release connector O-ring is damaged or has slipped, replace 

the fuel hose.  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Emission System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:24:50 AM

Page 24 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Бренд: Ford Страницы: 2
Air Lift WirelessAIR 73000EZ Manual preview
WirelessAIR 73000EZ
Бренд: Air Lift Страницы: 12
TUFLOC Dodge Charger TufBox Installation Instructions Manual preview
Dodge Charger TufBox
Бренд: TUFLOC Страницы: 6
Doug Thorley Headers THY-464-1 Instructions preview
THY-464-1
Бренд: Doug Thorley Headers Страницы: 5
Edelbrock 66002 Installation Instructions preview
66002
Бренд: Edelbrock Страницы: 2
Safe Fleet PRIME DESIGN VRR-NV200 Manual preview
PRIME DESIGN VRR-NV200
Бренд: Safe Fleet Страницы: 12
Hyundai Santa Fe 2019 Getting Started Manual preview
Santa Fe 2019
Бренд: Hyundai Страницы: 18
Safe Fleet PRIME DESIGN HRR-369-E-UM3-96 Manual preview
PRIME DESIGN HRR-369-E-UM3-96
Бренд: Safe Fleet Страницы: 12
Kocchi's 772161M1 Manual preview
772161M1
Бренд: Kocchi's Страницы: 4
BENDIX A-18 TRAILER ABS Manual preview
A-18 TRAILER ABS
Бренд: BENDIX Страницы: 40
Toyota RAV4 HV 2016 Quick Reference Manual preview
RAV4 HV 2016
Бренд: Toyota Страницы: 56
ULTIMATE SPEED 290923 Operation And Safety Notes preview
290923
Бренд: ULTIMATE SPEED Страницы: 56
Aston Martin V8 Vantage Workshop Manual preview
V8 Vantage
Бренд: Aston Martin Страницы: 415
BMW 325i 1991 Electrical Troubleshooting Manual preview
325i 1991
Бренд: BMW Страницы: 64
Buick 2006 LaCrosse Getting To Know Manual preview
2006 LaCrosse
Бренд: Buick Страницы: 20
National Cycle Quantum Wash'n'Wipe N30205 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30205
Бренд: National Cycle Страницы: 12
JAC HFC7151M1V-U221B Workshop Manual preview
HFC7151M1V-U221B
Бренд: JAC Страницы: 106
RAWLINK 36772 Instruction Manual preview
36772
Бренд: RAWLINK Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды