Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 425

Страница: 425 / 1056

INFORMATION AVAILABILITY

Verify related Service Bulletins

and/or on-line repair information
availability.

Is any related Service Bulletins

available?

the available Service Bulletins.

If the vehicle is not repaired, go to

the next step.

Go to the next step.

INSPECT TP SENSOR
CONNECTOR FOR POOR

CONNECTION

Turn the ignition switch off.

Disconnect the throttle body

connector.

Inspect for poor connection (such
as damaged/pulled-out pins,

corrosion).

Are there any malfunction?

Yes

Repair or replace suspected part, then go to
Step 9.

Go to the next step.

INSPECT TP SENSOR CIRCUIT

FOR SHORT TO GROUND

Turn the ignition switch to the ON
position (Engine off).

Inspect for continuity between TP

sensor terminal F (wiring harness-
side) and body ground

Is there continuity?

Yes

Repair or replace suspected part, then go to

Step 9.

Go to the next step.

INSPECT PCM CONNECTOR FOR
POOR CONNECTION

Turn the ignition switch off.

Disconnect the PCM connector.

Inspect for poor connection (such

as damaged/pulled-out pins,
corrosion).

Are there any malfunction?

Yes

Repair or replace suspected part, then go to
Step 9.

Go to the next step.

INSPECT TP SIGNAL CIRCUIT
FOR OPEN CIRCUIT

Inspect for continuity between

throttle body connector terminal F
(wiring harness-side) and PCM

terminal 2Z (wiring harness-side).

Is there continuity?

Yes

Go to the next step.

Repair or replace suspected part, then go to

Step 9.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:29 AM

Page 78

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды