manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

and/or on-line repair information 
availability.  

z

Is any related Service Bulletins 
available?  

the next step.  

No

Go to the next step.

3

VERIFY RELATED PENDING 

CODE OR STORED DTCs

 

z

Turn the ignition switch off then 
to the ON position (Engine off).  

z

Verify related pending code or 

stored DTCs.  

z

Are other DTCs present?  

Yes

Go to the appropriate DTC 

troubleshooting. 
(See 

DTC TABLE [MZI-3.5]

.)

No

Go to the next step.

4

INSPECT CKP SENSOR SIGNAL 

SENT TO PCM

 

z

Disable the inertia switch.  

z

Turn the ignition switch to the ON 
position [(Engine off).  

z

Access the PCM and monitor the 

RPM PID.  

z

Crank the engine.  

z

Is the engine speed more than 150 
rpm?  

NOTE:

z

The battery should be fully 

charged and the starting system 

should be functioning properly.  

Yes

Go to Step 13.

No

Go to the next step.

5

INSPECT TIMING COVER, CKP 

SENSOR AND EXTERNAL 
TRIGGER WHEEL (OUTSIDE 

TIMING COVER) FOR OBVIOUS 
PHYSICAL DAMAGE

 

z

Visually check the timing cover, 
CKP sensor and external trigger 

wheel (outside the timing cover) 
for obvious physical damage.  

z

Do any parts appear physically 

damaged?  

Yes

Repair if necessary. Then go to Step 13.

No

Go to Step.

6

INSPECT FOR PROPER CKP BIAS 
VOLTAGES IN PCM

 

z

Disconnect the CKP sensor 

Yes

Go to the next step.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:31 AM

Page 175 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Dakota Digital Retrotech RTX-68D-CHG Quick Start Manual preview
Retrotech RTX-68D-CHG
Бренд: Dakota Digital Страницы: 4
Whispbar K611W Fitting Instructions Manual preview
K611W
Бренд: Whispbar Страницы: 77
Pyle PLCMRV8B Black User Manual preview
PLCMRV8B Black
Бренд: Pyle Страницы: 4
Waeco MagicWatch MWE250 Installation And Operating Manual preview
MagicWatch MWE250
Бренд: Waeco Страницы: 172
GMC Envoy XUV 2004 Getting To Know Manual preview
Envoy XUV 2004
Бренд: GMC Страницы: 20
B-Speech Sima User Manual preview
Sima
Бренд: B-Speech Страницы: 4
GMC 2010 Tahoe Owner'S Manual preview
2010 Tahoe
Бренд: GMC Страницы: 120
Prime Tech H-066 User Manual preview
H-066
Бренд: Prime Tech Страницы: 6
Mercedes-Benz 2016 SLK Operator'S Manual preview
2016 SLK
Бренд: Mercedes-Benz Страницы: 358
Dodge Challenger 2013 Owner'S Manual preview
Challenger 2013
Бренд: Dodge Страницы: 543
Metra Electronics 99-5819 Installation Instructions Manual preview
99-5819
Бренд: Metra Electronics Страницы: 8
Cadillac XT4 2022 Convenience/Personalization Manual preview
XT4 2022
Бренд: Cadillac Страницы: 20
Black Horse Off Road TO20 Installation Instructions Manual preview
TO20
Бренд: Black Horse Off Road Страницы: 7
Racelogic Speed & Route Profiler Manual preview
Speed & Route Profiler
Бренд: Racelogic Страницы: 24
ECS FIA-030-B Fitting Instructions preview
FIA-030-B
Бренд: ECS Страницы: 4
Whispbar WB751 Manual preview
WB751
Бренд: Whispbar Страницы: 15
RAM Truck 2014 Owner'S Manual preview
Truck 2014
Бренд: RAM Страницы: 330
Cadillac 2004 Seville Customer Convenience/Personalization Manual preview
2004 Seville
Бренд: Cadillac Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды