manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

z

Is any related Service Bulletins 

available?  

No

Go to the next step.

3

INSPECT FUEL INJECTOR NO.2 

CONNECTOR FOR POOR 
CONNECTION

 

z

Turn the ignition switch off.  

z

Disconnect the fuel injector No.2 

connector.  

z

Inspect for poor connection (such as 

damaged/pulled-out pins, 
corrosion).  

z

Are there malfunction?  

Yes

Repair or replace suspected part, then go 

to Step 8.

No

Go to the next step.

4

INSPECT PCM CONNECTOR FOR 

POOR CONNECTION

 

z

Turn the ignition switch off.  

z

Disconnect the PCM connector.  

z

Inspect for poor connection (such as 

damaged/pulled-out pins, 
corrosion).  

z

Is there malfunction?  

Yes

Repair or replace suspected part, then go 

to Step 8.

No

Go to the next step.

5

INSPECT FUEL INJECTOR NO.2 

POWER SUPPLY CIRCUIT FOR 
OPEN CIRCUIT

 

z

Turn the ignition switch to the ON 
position (Engine off).  

z

Measure the voltage between fuel 

injector No.2 connector terminal B 
and body ground.  

z

Is the voltage 

B+

 ?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go 
to Step 8.

6

INSPECT FUEL INJECTOR NO.2 

SIGNAL CIRCUIT FOR OPEN 
CIRCUIT

 

z

Inspect continuity between fuel 
injector No.2 terminal A (wiring 

harness-side) and PCM terminal 
2BM (wiring harness-side).  

z

Is there continuity?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go 

to Step 8.

7

INSPECT FUEL INJECTOR NO.2

 

Yes

Replace the fuel injector No.2, then go 

to the next step.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:30 AM

Page 126 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Saab 99 Important Operatlng, Safety And Maintenance Instructions preview
99
Бренд: Saab Страницы: 75
Happy Orange USB-C Quick Start Manual preview
USB-C
Бренд: Happy Orange Страницы: 2
Whispbar K783W Fitting Instructions Manual preview
K783W
Бренд: Whispbar Страницы: 16
Quadratec Brute Strength 12057.0271 Installation Manual preview
Brute Strength 12057.0271
Бренд: Quadratec Страницы: 6
Ironton 44596 Owner'S Manual preview
44596
Бренд: Ironton Страницы: 7
STC 552-010 Installation Instructions Manual preview
552-010
Бренд: STC Страницы: 6
Boyo VTL17LTJ Manual preview
VTL17LTJ
Бренд: Boyo Страницы: 9
E&G Classics 1398-0502-09 Instruction Manual preview
1398-0502-09
Бренд: E&G Classics Страницы: 2
APS IA06SJD4B Installation Instructions preview
IA06SJD4B
Бренд: APS Страницы: 3
TATA Motors Indigo eCS Owner'S Manual & Service Book preview
Indigo eCS
Бренд: TATA Motors Страницы: 166
Advanced Diagnostics MVP PRO Manual preview
MVP PRO
Бренд: Advanced Diagnostics Страницы: 10
TomTom LINK 105 Installation Manual preview
LINK 105
Бренд: TomTom Страницы: 22
Whispbar WB201 Manual preview
WB201
Бренд: Whispbar Страницы: 14
Volvo V70 2014 Quick Manual preview
V70 2014
Бренд: Volvo Страницы: 16
Tesla Gen 3 Manual preview
Gen 3
Бренд: Tesla Страницы: 42
Whispbar K423W Fitting Instructions Manual preview
K423W
Бренд: Whispbar Страницы: 18
HawksHead TRACK MASTER Instruction Manual preview
TRACK MASTER
Бренд: HawksHead Страницы: 10
Telwin ST 160 Instruction Manual preview
ST 160
Бренд: Telwin Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды