Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 680

Страница: 680 / 1056

DTC P0690 (MZI-3.5) DIAGNOSTIC PROCEDURE

STEP

INSPECTION

ACTION

VERIFY FREEZE FRAME DATA
HAS BEEN RECORDED

Has FREEZE FRAME DATA been

recorded?

Yes

Go to the next step.

Record FREEZE FRAME DATA on the
repair order, then go to the next step.

VERIFY RELATED REPAIR

INFORMATION AVAILABILITY

Verify related Service Bulletins
and/or on-line repair information

availability.

Is any related Service Bulletins
available?

Yes

Perform repair or diagnosis according to

the available Service Bulletins.

If the vehicle is not repaired, go to
the next step.

Go to the next step.

INSPECT ALL OTHER PATS DTCs

Repair all other PATS DTCs before
P0690.

(see

IMMOBILIZER SYSTEM

COMPONENT

REPLACEMENT/KEY
ADDITION AND CLEARING

[ADVANCED KEYLESS
SYSTEM]

(see

IMMOBILIZER SYSTEM

COMPONENT
REPLACEMENT/KEY

ADDITION AND CLEARING
[KEYLESS ENTRY SYSTEM]

Have all other PATS DTCs been
diagnosed?

Yes

Go to the next step.

(see

IMMOBILIZER SYSTEM

COMPONENT REPLACEMENT/KEY

ADDITION AND CLEARING
[ADVANCED KEYLESS SYSTEM]

(see

IMMOBILIZER SYSTEM

COMPONENT REPLACEMENT/KEY

ADDITION AND CLEARING
[KEYLESS ENTRY SYSTEM]

INSPECT IGNITION SWITCH

POSITION RUN CIRCUIT SHORT
TO POWER SUPPLY

Turn the ignition switch off.

Measure the voltage between PCM
terminal 1BD (wiring harness-side)

and body ground.

Is the voltage

B+

Yes

Repair or replace suspected part, then go

to Step 6.

Go to the next step.

INSPECT FOR CORRECT PCM

Yes

Go to the next step.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:36 AM

Page 333

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды