manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

ignition switch to ON position? 
(see 

FUEL LINE PRESSURE 

INSPECTION [MZI-3.5]

 .)

(see 

FUEL PUMP UNIT 

REMOVAL/INSTALLATION [MZI-

3.5]

 .) 

High:

  

Replace the fuel pump unit. 

(see 

FUEL PUMP UNIT 

REMOVAL/INSTALLATION [MZI-

3.5]

 .)

11

Connect pressure gauge to the A/C low 
and high side pressure lines.Turn the 

A/C on and measure low side and high 
side pressures.Are pressures within 

specifications?(see 

REFRIGERANT 

PRESSURE CHECK

 .)

NOTE:

z

The following test is for engine 

stalling with the A/C on 
concern. If other symptoms 

exist, go to the next step.  

Yes

Go to the next step.

No

If A/C is always on, go to symptom 
troubleshooting "No.24 A/C is always 

on or A/C compressor runs 
continuously". 

(See 

NO.24 A/C IS ALWAYS ON OR 

A/C COMPRESSOR RUNS 

CONTINUOUSLY [MZI-3.5]

.) 

For other symptoms, inspect the 

following: 

z

Refrigerant charging amount  

z

Condenser fan operation  

12

Inspect for A/C cut-off operation. 

(See 

ENGINE CONTROL SYSTEM 

OPERATION INSPECTION [MZI-

3.5]

.) 

Does the A/C cut-off function 
properly?

Yes

Go to the next step.

No

Inspect A/C cut-off system components.

13

Disconnect the vacuum hose between 

the purge solenoid valve and the intake 
manifold from purge solenoid valve 

side. 
Plug opening end of vacuum hose. 

Drive the vehicle. 
Does the engine condition improve?

Yes

Inspect if purge solenoid valve is stuck 

open mechanically. 
Inspect the evaporative emission control 

system. 
(See 

ENGINE CONTROL SYSTEM 

OPERATION INSPECTION [MZI-
3.5]

.)

No

Go to the next step.

14

Visually inspect the CMP sensor and 
projections of camshaft pulley. 

Are the CMP sensor and projections of 
camshaft pulley normal?

Yes

Go to the next step.

No

Replace the malfunctioning part.

15

Inspect the variable valve timing 

control system operation. 
(See 

ENGINE CONTROL SYSTEM 

OPERATION INSPECTION [MZI-
3.5]

.) 

Does the variable valve timing control 
system function properly?

Yes

Go to the next step.

No

Repair or replace the malfunctioning 
part according to variable valve timing 

control system inspection results.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:37 AM

Page 57 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

LaserTrack Flare Installation Manual preview
Flare
Бренд: LaserTrack Страницы: 12
Kargo Master 40020 Assembly Manual preview
40020
Бренд: Kargo Master Страницы: 6
PAC SWI-RC Installation Instructions preview
SWI-RC
Бренд: PAC Страницы: 4
PAC RP4-CH11 Manual preview
RP4-CH11
Бренд: PAC Страницы: 4
PAC BCI-CH41 User Manual preview
BCI-CH41
Бренд: PAC Страницы: 8
PAC C2R-CHY4 Installation Instructions preview
C2R-CHY4
Бренд: PAC Страницы: 5
Code 3 21 COVERT Series Installation And Operation Instructions Manual preview
21 COVERT Series
Бренд: Code 3 Страницы: 16
Chevrolet Avalanche 2005 Owner'S Manual preview
Avalanche 2005
Бренд: Chevrolet Страницы: 494
Victory 4x4 5TH GEN 4RUNNER Install Instructions preview
5TH GEN 4RUNNER
Бренд: Victory 4x4 Страницы: 5
Keith WALKING FLOOR Helpful Hints preview
WALKING FLOOR
Бренд: Keith Страницы: 2
Whispbar K604W Fitting Instructions Manual preview
K604W
Бренд: Whispbar Страницы: 15
Fast Master Products SWIVELWHEEL-46 Assembly Instructions Manual preview
SWIVELWHEEL-46
Бренд: Fast Master Products Страницы: 13
Meta System FrontPlate4 Manual preview
FrontPlate4
Бренд: Meta System Страницы: 16
Cadillac 54-6219 1954 Shop Manual preview
54-6219 1954
Бренд: Cadillac Страницы: 409
Fortin THAR-AUD1 Manual preview
THAR-AUD1
Бренд: Fortin Страницы: 9
Paccar PACCHARGE AC20 Installation Manual preview
PACCHARGE AC20
Бренд: Paccar Страницы: 63
APS IA06SJD4B Installation Instructions preview
IA06SJD4B
Бренд: APS Страницы: 3
Safe Fleet PRIME DESIGN HRR3-E-PM42 Manual preview
PRIME DESIGN HRR3-E-PM42
Бренд: Safe Fleet Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды