Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 383

Страница: 383 / 1056

Is any related Service Bulletins

available?

Go to the next step.

INSPECT OCV (LH) CONNECTOR

FOR POOR CONNECTION

Turn the ignition switch off.

Disconnect the OCV (LH)
connector.

Inspect for poor connection (such
as damaged/pulled-out pins,

corrosion).

Are there any malfunction?

Yes

Repair or replace suspected part, then go to

Step 10.

Go to the next step.

INSPECT OCV (LH)

Inspect the OCV (LH).

(see

OIL CONTROL VALVE

(OCV) INSPECTION [MZI-
3.5].

)

Is there any malfunction?

Yes

Replace the OCV (LH), then go to Step 10.
(see

OIL CONTROL VALVE (OCV)

REMOVAL/INSTALLATION [MZI-
3.5].

)

Go to the next step.

INSPECT OCV (LH) CIRCUIT FOR
OPEN CIRCUIT

Turn the ignition switch to the ON

position (Engine off).

Measure the voltage between the
OCV (LH) connector terminal A

(wiring harness-side) and body

ground.

Is the voltage B+?

Yes

Go to the next step.

Repair or replace suspected part, then go to

Step 10.

INSPECT OCV (LH) CIRCUIT FOR
SHORT TO POWER SUPPLY

Disconnect the PCM connector.

Turn the ignition switch to the ON

position (Engine off).

Measure the voltage between the

OCV (LH) connector terminal B
and body ground.

Is the voltage B+?

Yes

Repair or replace suspected part, then go to
Step 10.

Go to the next step.

INSPECT OCV (LH) CIRCUIT FOR

SHORT TO GROUND

Yes

Repair or replace suspected part, then go to

Step 10.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:29 AM

Page 36

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды