Hino 238 Workshop Manual Download Page 39

Page: 39 / 919

ENGINE CONTROL SYSTEM (J08E)

4–816

INSPECTION PROCEDURE: P141F

Set the starter switch to the "LOCK" position.

Connect the vehicle to Hino-DX.

Set the starter switch to the "ON" position.

Select [Engine] and check if P141F has been detected in [Fault
Information].

YES

Check the DTC detected (Engine ECU) [Hino-DX]

Select

Engine

SAPH16F010300653

Has DTC P141F been detected?

Go to DTC separate trouble diagnosis of the
burner system (BCU).

Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands