Hino 238 Workshop Manual Download Page 302

Page: 302 / 919

ENGINE CONTROL SYSTEM (J08E)

4–1079

P2229: Barometric pressure sensor - out of range (out of range high)

INFORMATION

1. Technical description

<Description of malfunction>

•

The atmospheric pressure sensor (inside the ECU) is not properly functioning.

2. DTC set condition

(1) DTC detection condition

•

Starter switch ON.

•

Battery voltage is in the range of 10 V to 16 V, and Engine stall, or Engine speed

≥

500 r/min for 5 seconds.

(2) Judgement criteria

•

Barometric pressure sensor voltage

4.2 V (120 kPa {17.4 psi})

•

Failure timer

≥

3 seconds

3. Reset condition

•

Just after restoration to normal condition.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

•

Engine output is restricted.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Engine output is insufficient.

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check that the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is stored after test drive.

8. Estimated failure factors

•

Malfunction of engine ECU

Common rail
pressure sensor

Boost pressure
sensor

Engine
ECU

K2A

(VCC)

(PCR+)

K2B

KRQ

(SIG)

(AVC2)

(PCR3)

(ATI+)

(PIM)

K2C

KUG

(GND)

(AGD4)

K6G

LLJ

VCC2

GND1

SIG1

VCC1

GND2

SIG2

SAPH16F010300830

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands