manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

DEF SCR SYSTEM (DCU)

5–220

INSPECTION PROCEDURE: P20A3

1.

Check the connection of the DEF pump connector (Looseness and
poor contact).

NO

YES

1.

Set the starter switch to the "LOCK" position.

2.

Disconnect the DEF pump connector.

3.

Use the electrical tester to measure the resistance between the
terminals of the DEF pump (reverting valve).

NO

YES

1

Inspect the DEF pump (reverting valve) connector

Was any failure found?

Connect securely, repair if needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 2.

2

Inspect the DEF pump (reverting valve) unit

PMV+

PMV-

SAPH16F020400145

Measurement 

conditions

Tester 

connections

Standard values

Starter switch: 
LOCK

DEF pump 
(Reverting valve) 
connector
PMV+ 

–

 PMV-

23 

C {73.4 

F}: 

2.05 

–

 12.05 

Do the measurements meet the standard value?

Go to step 3.

Replace the DEF pump.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Kargo Master 40640 Assembly Manual preview
40640
Brand: Kargo Master Pages: 5
Cadillac ESCALADE - BROCHURE 2009 Personalization Manual preview
ESCALADE - BROCHURE 2009
Brand: Cadillac Pages: 24
Cadillac Escalade Personalization Manual preview
Escalade
Brand: Cadillac Pages: 20
Cadillac Escalade 2016 Convenience/Personalization Manual preview
Escalade 2016
Brand: Cadillac Pages: 20
Jeep Wrangler 2011 Owner'S Manual preview
Wrangler 2011
Brand: Jeep Pages: 603
Jeep Patriot 2011 User Manual preview
Patriot 2011
Brand: Jeep Pages: 80
Bimmer Jakes FRONT HEADLIGHT LENS COVER Replacement Manual preview
FRONT HEADLIGHT LENS COVER
Brand: Bimmer Jakes Pages: 4
Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Brand: Ford Pages: 2
Mobis G4211ADE00AL Installation Instructions Manual preview
G4211ADE00AL
Brand: Mobis Pages: 16
Subaru starlink Manual preview
starlink
Brand: Subaru Pages: 216
Metra Electronics 70-5511 Installation Instructions preview
70-5511
Brand: Metra Electronics Pages: 2
Hama 00201510 Operating Instructions Manual preview
00201510
Brand: Hama Pages: 40
GReddy Intercooler Kit Type 31 Installation Manual preview
Intercooler Kit Type 31
Brand: GReddy Pages: 9
VDO VIEWLINE 52 MM - MOUNTING 11-09 Installation Instructions preview
VIEWLINE 52 MM - MOUNTING 11-09
Brand: VDO Pages: 4
v.link NAL-PC-HSD Manual preview
NAL-PC-HSD
Brand: v.link Pages: 21
Kogan CERTA CTCVINCVR14A User Manual preview
CERTA CTCVINCVR14A
Brand: Kogan Pages: 4
SMART EQ forfour 2018 Owner'S Manual preview
EQ forfour 2018
Brand: SMART Pages: 224
Metra Electronics 95-7617B Installation Instructions Manual preview
95-7617B
Brand: Metra Electronics Pages: 8

Brands by name

Popular brands

Load more brands