manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

DEF SCR SYSTEM (DCU)

5–1

DEF SCR SYSTEM (DCU)

5-001

5

DEF SCR SYSTEM ......................................................5-2

PRECAUTIONS FOR DIAGNOSIS.........................5-2
SYSTEM BLOCK DIAGRAM...................................5-4
SYSTEM DIAGRAM................................................5-5
SENSOR LOCATION ..............................................5-6
COMPUTER (DCU) WIRE HARNESS
CONNECTOR PIN ASSIGNMENT .........................5-8
SIGNAL CHECK HARNESS ...................................5-9
INSPECTION ..........................................................5-9
MALFUNCTION INDICATOR LIGHT
ILLUMINATION PATTERN ....................................5-10
DIAGNOSIS USING THE PC DIAGNOSIS
TOOL.....................................................................5-10
DIAGNOSTIC TROUBLE CODE (DTC)
TABLE ...................................................................5-12
DTC: P0071 ..........................................................5-17
DTC: P0072 ..........................................................5-32
DTC: P0073 ..........................................................5-42
DTC: P0562 ..........................................................5-52
DTC: P0563 ..........................................................5-56
DTC: P060C..........................................................5-60
DTC: P062F ..........................................................5-63
DTC: P0667 ..........................................................5-66
DTC: P0668 ..........................................................5-69
DTC: P0669 ..........................................................5-72
DTC: P068A ..........................................................5-75
DTC: P142A ..........................................................5-83
DTC: P142B ..........................................................5-88
DTC: P202E ........................................................5-103
DTC: P203C........................................................5-110
DTC: P203D........................................................5-114
DTC: P2044 ........................................................5-118
DTC: P2045 ........................................................5-122
DTC: P2047 ........................................................5-126
DTC: P2048 ........................................................5-129
DTC: P2049 ........................................................5-135
DTC: P204B ........................................................5-142
DTC: P204C........................................................5-146
DTC: P204D........................................................5-153
DTC: P205B ........................................................5-160
DTC: P205C........................................................5-173
DTC: P205D........................................................5-177
DTC: P206A ........................................................5-181
DTC: P208A ........................................................5-185
DTC: P208B ........................................................5-190
DTC: P208C........................................................5-193

DTC: P208D........................................................5-197
DTC: P20A0 ........................................................5-201
DTC: P20A1 ........................................................5-208
DTC: P20A2 ........................................................5-212
DTC: P20A3 ........................................................5-219
DTC: P20B1 ........................................................5-225
DTC: P20B2 ........................................................5-231
DTC: P20B3 ........................................................5-243
DTC: P20B4 ........................................................5-249
DTC: P20E8 ........................................................5-255
DTC: P20E9 ........................................................5-266
DTC: P20F4 ........................................................5-274
DTC: P2201 ........................................................5-281
DTC: P2202 ........................................................5-294
DTC: P2203 ........................................................5-298
DTC: P2204 ........................................................5-302
DTC: P2209 ........................................................5-312
DTC: P2212 ........................................................5-323
DTC: P2215 ........................................................5-334
DTC: P2216 ........................................................5-338
DTC: P2222 ........................................................5-342
DTC: P2481 ........................................................5-353
DTC: P2482 ........................................................5-360
DTC: P2483 ........................................................5-368
DTC: P2510 ........................................................5-386
DTC: P2BAE .......................................................5-393
DTC: U0029 ........................................................5-404
DTC: U0038 ........................................................5-407
DTC: U0100 ........................................................5-410
DTC: U029D........................................................5-415
DTC: U029E........................................................5-418
DTC: U02A2........................................................5-421
DTC: U0597 ........................................................5-424

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Quadratec QR3 Installation Manual preview
QR3
Brand: Quadratec Pages: 8
Toyota RX450h 2010 Emergency Response Manual preview
RX450h 2010
Brand: Toyota Pages: 35
Air Lift WirelessAIR 73000EZ Manual preview
WirelessAIR 73000EZ
Brand: Air Lift Pages: 12
Brodit ProClip 853660 Manual preview
ProClip 853660
Brand: Brodit Pages: 2
Power Fist 8985988 Manual preview
8985988
Brand: Power Fist Pages: 12
EAL EUFAB 16491 Operating Instructions Manual preview
EUFAB 16491
Brand: EAL Pages: 7
Trailboss QTHD519L Fitting Instructions Manual preview
QTHD519L
Brand: Trailboss Pages: 8
EUFAB 11556 Operating Instructions Manual preview
11556
Brand: EUFAB Pages: 52
Caltrend BM110 Installation Instructions preview
BM110
Brand: Caltrend Pages: 2
Advanced ICE 1296-1 Manual preview
1296-1
Brand: Advanced ICE Pages: 4
Yakima Prorack K436 Fitting Instructions Manual preview
Prorack K436
Brand: Yakima Pages: 13
Gator GHWCUSB2 User Manual preview
GHWCUSB2
Brand: Gator Pages: 8
benbat BM721 Instructions For Use Manual preview
BM721
Brand: benbat Pages: 14
SPL FE Z33 Installation Instructions preview
FE Z33
Brand: SPL Pages: 5
Dodge 2005 JR41 Stratus Owner'S Manual preview
2005 JR41 Stratus
Brand: Dodge Pages: 293
Honda 1991 Civic Online Reference Owner'S Manual preview
1991 Civic
Brand: Honda Pages: 124
r.LiNK RL2-MMI3G-GW Manual preview
RL2-MMI3G-GW
Brand: r.LiNK Pages: 21
Lantronix FOX3 Series Hardware Manual preview
FOX3 Series
Brand: Lantronix Pages: 51

Brands by name

Popular brands

Load more brands