Hino 238 Workshop Manual Download Page 271 | Manualshive

Page: 271 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–1048

3

Inspect for
short-circuit of
the injector
wire harness
(between
injector linked-
up connector
and injector
harness con-
nector)

Disconnect the injector harness
connector and measure the resis-
tance between each terminal in
the injector linked-up connector
(engine side) and ground.
<Tester connections>
injector linked-up connector
(engine side)
#4 injector:
7

–

Ground

8

–

Ground

#5 injector:
1

–

Ground

2

–

Ground

#6 injector:
9

–

Ground

10

–

Ground

<Standard values>





The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 4.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

4

Inspect dis-
connection of
the injector
harness

Measure the resistance between
the #4

–

#6 injector harness con-

nector terminals.
<Tester connections>
Injector harness connector termi-
nals
#4 IJ4-

–

IJ4+

#5 IJ5-

–

IJ5+

#6 IJ6-

–

IJ6+

<Standard values>
20



C {68



F}: 0.37

–

0.57



The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 5.

Go to step 6.

5

Inspect the
injector unit

Measure the resistance between
the #4

–

#6 injector terminals and

the injector bodies.
<Tester connections>
injector terminals

–

injector bod-

ies
<Standard values>
10 M



or more

The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Replace the
injector har-
ness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Replace the
injector.
Perform "After-
inspection
work" of
INFORMA-
TION section.

6

Check the
DTC detected
(Engine ECU)
[Hino-DX]

Check if the DTC (P2150 or
P2151) has been detected in
[Engine].

DTC (P2150
or P2151) has
been detected:
Go to YES.

No DTC has
been detected:
Go to NO.

Replace the
engine ECU.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Procedure
completed.
Perform "After-
inspection
work" of
INFORMA-
TION section.

DTC: P2150

Fuel injector driver circuit 2

- circuit (circuit low)

Inspection procedure

DTC: P2151

Fuel injector driver circuit 2

- circuit (circuit high)

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

«
...
269
270
271
272
273
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Brand: AccuAir Pages: 40

Brand: Peak Pages: 10

Brand: GMC Pages: 20

Car Top Duffle Bag

Brand: Rightline Gear Pages: 2

Brand: EUFAB Pages: 12

Brand: Lexus Pages: 369

Brand: Mountain Top Pages: 12

PRIME DESIGN VBI-FT21B

Brand: Safe Fleet Pages: 12

Plusone Console 4521011B

Brand: Honda Pages: 4

1506-PHX Cargo Plus

Brand: Ranger design Pages: 8

Brand: AUTOTECH Pages: 1

Brand: Cadillac Pages: 402

Brand: Cobra Pages: 2

FXX ATM Emulator

Brand: BMW Pages: 5

Brand: Whispbar Pages: 14

Brand: Whispbar Pages: 15

C-Max Energi 2014

Brand: Ford Pages: 10

Brand: Audi Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands