manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–952

4

Inspect the 
exhaust gas 
temperature 
sensor (SCR 
inlet) connec-
tor

Check the connection of the 
exhaust gas temperature sensor 
(SCR inlet) connector (Looseness 
and poor contact).

Failure found: 
Go to YES.

No failure 
found: Go to 
NO.

Connect 
securely, 
repair if 
needed.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Go to step 5.

5

Inspect the 
exhaust gas 
temperature 
sensor (SCR 
inlet)

 

1.

Check the installation of the 
exhaust gas temperature 
sensor (SCR inlet).

2.

Make sure there is no dirt or 
damage to the exhaust gas 
temperature sensor (SCR 
inlet).

Failure found: 
Go to YES.

No failure 
found: Go to 
NO.

Clean the 
exhaust gas 
temperature 
sensor (SCR 
inlet) and 
install it prop-
erly.
If damaged, 
replace the 
sensor.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Go to step 6.

6

Inspect the 
exhaust gas 
temperature 
sensor (SCR 
inlet) unit

Disconnect the exhaust gas tem-
perature sensor (SCR inlet) con-
nector and measure the 
resistance between the terminals 
of the sensor (FAT+ 

–

 FAT-).

<Standard values>
20 

C {68 

F}: 220 

The measure-
ments meet 
the standard 
value: Go to 
YES.

The measure-
ments do not 
meet the stan-
dard value: Go 
to NO.

Go to step 7.

Replace the 
sensor.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

7

Check the 
DEF pipe 
(pump 

 

injector)

Check the DEF pipe (pressure 
line) and verify that there are no 
disconnections, clogging, corro-
sion, or cracks.

Failure found: 
Go to YES.

No failure 
found: Go to 
NO.

Repair or 
replace the 
faulty part.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Go to step 8.

DTC: P20EE

NOx converting catalyst conversion efficiency

Inspection procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Back View RV-250 User Manual preview
RV-250
Brand: Back View Pages: 168
Ignition 63-231 Quick Start preview
63-231
Brand: Ignition Pages: 1
Alpine KCE-G7QI Installation preview
KCE-G7QI
Brand: Alpine Pages: 2
Whispbar K896W Fitting Instructions Manual preview
K896W
Brand: Whispbar Pages: 15
Camcar 40108 Mounting Instructions preview
40108
Brand: Camcar Pages: 6
ABL eMH3 Quick Start Manual preview
eMH3
Brand: ABL Pages: 4
Pyle PLCMRV8B Black User Manual preview
PLCMRV8B Black
Brand: Pyle Pages: 4
Renault Lodgy 2017 Driver'S Handbook Manual preview
Lodgy 2017
Brand: Renault Pages: 238
Big Mikes Performance Parts STO N SHO SNS 144 Installation Procedures Manual preview
STO N SHO SNS 144
Brand: Big Mikes Performance Parts Pages: 7
Lincoln MKZ 2018 Quick Reference Manual preview
MKZ 2018
Brand: Lincoln Pages: 10
Xhorse VVDI User Manual preview
VVDI
Brand: Xhorse Pages: 48
Ranger design 1525-FTR Installation Manual preview
1525-FTR
Brand: Ranger design Pages: 24
Vauxhall 2013 Ampera Infotainment Manual preview
2013 Ampera
Brand: Vauxhall Pages: 95
Ford Focus 2008 Quick Reference Manual preview
Focus 2008
Brand: Ford Pages: 2
ULTIMATE SPEED 290923 Operation And Safety Notes preview
290923
Brand: ULTIMATE SPEED Pages: 56
Grillo PK 1400 Operator'S Manual preview
PK 1400
Brand: Grillo Pages: 71
Reliant ROBIN 850 Workshop Manual preview
ROBIN 850
Brand: Reliant Pages: 206
Skoda FABIA II TMB PS 035 Mounting And User Instructions preview
FABIA II TMB PS 035
Brand: Skoda Pages: 16

Brands by name

Popular brands

Load more brands